| Table 1: | Instrument Panel Module Scan Tool Data Parameters |
| Table 2: | Instrument Panel Module Scan Tool Output Controls |
Parameter | System State | Expected Value | Description |
|---|---|---|---|
Operating Conditions: Ignition ON | |||
Accessory LED Duty Cycle | -- | Varies | This displays %. |
Accessory Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the accessory relay. |
Adjusted Battery Current | -- | Varies | This displays amps. |
Battery Voltage Signal | -- | Varies | This displays Volts. This is the current battery voltage signal. |
BPP Sensor | -- | Varies | This displays Counts. This is the current brake pedal position (BPP) measured in counts. |
BPP Sensor Reference | -- | Varies | This displays Counts. This is the brake pedal position (BPP) sensor reference measured in counts. |
BPPS High During Learn | -- | No | The scan tool displays Yes or No. Yes is displayed if the brake pedal position sensor (BPPS) was high during learn. |
BPPS Learned Home Position | -- | Varies | This displays Volts. This is the brake pedal position sensor (BPPS) home position measured in volts. |
BPPS Low During Learn | -- | No | The scan tool displays Yes or No. Yes is displayed if the brake pedal position sensor (BPPS) was low during learn. |
BPPS Move During Learn | -- | No | The scan tool displays Yes or No. Yes is displayed if the brake pedal position sensor (BPPS) was moved during learn. |
BPPS Status | -- | Learned | The scan tool displays Learned, Unlearned, Undecided or Invalid. Learned is displayed if the brake pedal position sensor (BPPS) is calibrated properly. |
Calculated Brake Pedal Position | -- | Varies | This displays Counts. This is the current brake pedal position measured in counts. |
Cigar Lighter Relay | -- | Off | The scan tool displays On or Off. This is the state of the cigarette lighter relay. |
Courtesy Lamp Switch | -- | Off | The scan tool displays On or Off. This is the state of the courtesy lamp switch. |
Column Lock Relay | -- | Disabled | The scan tool displays Enabled or Disabled. This is the state of the column lock relay. |
Cruise | -- | Varies | This displays Counts. This is the state of the cruise switch measured in counts. |
Dimming potentiometer | -- | OK | The scan tool displays OK or Failed. |
Dimming Required | -- | No | The scan tool displays Yes or No. |
Estimated Battery Temp. | -- | Varies | This displays °C (°F). This is the current estimated battery temperature. |
Flash to Pass Switch | -- | Inactive / Off | The scan tool displays Active / Inactive or On / Off. This is the state of the flash to pass switch. |
Front Foglamp Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the front foglamp relay. |
Hazard Lamp Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the hazard lamp switch. |
Hazard Lamps | -- | Disabled | The scan tool displays Enabled or Disabled. This is the state of the hazard lamps. |
Headlamp Switch | -- | Off | The scan tool displays On or Off. This is the state of the headlamp switch. |
Headlamp Washer Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the headlamp washer relay. |
Headlamp Washer Switch | -- | Off | The scan tool displays On or Off. This is the state of the headlamp washer switch. |
Headlamp/Parklamp Off Switch | -- | Off | The scan tool displays On or Off. This is the state of the headlamp / parklamp off switch. |
High Beam Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the high beam relay. |
High Beam Select Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the high beam select switch. |
Horn Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the horn relay. |
Ignition Mode Switch | -- | Varies | This displays Volts. This is the current voltage at the ignition mode switch. |
Incandescent Dimming | -- | Varies | This displays %. This is the interior lighting dimming percentage. |
Key Cylinder Halo Lamp | -- | Varies | This displays %. This is the dimming percentage at the key cylinder. |
Learn in Progress | -- | No | The scan tool displays Yes or No. Yes is displayed if the brake pedal position sensor (BPPS) is in learn mode. |
LED Dimming | -- | Varies | This displays %. This is the backlighting dimming percentage. |
Lights On With Wipers | -- | Off | The scan tool displays On or Off. |
Low Beam Relay Status | -- | No | The scan tool displays Yes or No. This is the state of the low beam relay. |
OFF LED Duty Cycle | -- | Varies | This displays %. |
Park Lamp Switch | -- | Off | The scan tool displays On or Off. This is the state of the park lamp switch. |
Park Position Input | -- | In Park | The scan tool displays Out of Park or In Park. In Park is displayed if the vehicle transmission is in park. |
Parkgear Home Position Switch | -- | Varies | The scan tool displays On or Off. |
Parking Brake Switch | -- | Released | The scan tool displays Applied or Released. This is the state of the parking brake switch. |
Parklamp Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the parklamp relay. |
Personalization Status | -- | Varies | The scan tool displays Driver 1, Driver 2 or Unknown. |
Photocell State | -- | Varies | The scan tool displays Day or Night. |
PRNDL State | -- | Park | The scan tool displays Park or Not in Park. Park is displayed if the transmission gear is in park. |
Remote Start Attempts | -- | Varies | The scan tool displays a numeric value from 0-10. |
Remote Start Equipped | -- | Varies | The scan tool displays Active or Inactive. |
Remote Start Request | -- | No | The scan tool displays Yes or No. |
Remote Starts Remaining | -- | Varies | The scan tool displays a numeric value from 0-10. |
Run Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the run relay. |
Run/Crank Relay Status | -- | Off | The scan tool displays On or Off. This is the state of the run/crank relay. |
SIR Lighting | -- | Disabled | The scan tool displays Enabled or Disabled. This is the state of the SIR lighting. |
Smart Beam Status | -- | Enabled | The scan tool displays Enabled or Disabled. This is the state of the smart beam. |
Start LED Duty Cycle | -- | Varies | This displays %. |
Steering Wheel Controls Return | -- | Varies | This displays Counts. |
Steering Wheel Position Sensor | -- | Varies | This displays Counts. This is the position of the steering wheel measured in counts. |
Stop Lamp Status | -- | Off | The scan tool displays On or Off. This is the state of the stop lamps. |
Stoplamp Relay | -- | Released | The scan tool displays Applied or Released. This is the state of the stoplamp relay. |
Tap Up/Down Enable | -- | Disabled | The scan tool displays Enabled or Disabled. |
Telescope Forward Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the telescope forward switch. |
Telescope Rearward Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the telescope rearward switch. |
Tilt Down Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the tilt down switch. |
Tilt Up Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the tilt up switch. |
Traction Control Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the traction control switch. |
Twilight Enable | -- | Varies | The scan tool displays Enabled or Disabled. |
Valet Switch | -- | Inactive | The scan tool displays Active or Inactive. This is the state of the valet switch. |
Output Control | Description |
|---|---|
Accessory LED | This output control is used to command the Accessory LED ON or OFF. |
Air Quality Sensitivity Level | This output control is used to control the air quality sensitivity level. |
BPP Sensor Calibration | This output control is used to calibrate the brake pedal position (BPP) sensor. |
Column Lock Relay Enable | This output control is used to command the column lock relay enable function. |
Front Fog Lamps | This output control is used to command the front fog lamps ON or OFF. |
Headlamp Washer | This output control is used to select a headlamp washer ON or OFF. |
High Beams | This output control is used to command the front high beams ON or OFF. |
Horn | This output control is used to command the horn ON or OFF. |
Idle Boost Level 1 | This output control is used to increase percentage or amperage of the idle boost level 1. Boost increases engine speed in the event that there is a low battery condition. |
Idle Boost Level 2 | This output control is used to increase percentage or amperage of the idle boost level 2. Boost increases engine speed in the event that there is a low battery condition. |
Idle Boost Level 3 | This output control is used to increase percentage or amperage of the idle boost level 3. Boost increases engine speed in the event that there is a low battery condition. |
Ignition Switch LED Power | This output control is used to command the Accessory, Off and Start LEDs around the start switch ON or OFF. |
Incandescent Dimming | This output control is used to control the incandescent dimming from 0-100 percent by 20 percent increments when INCREASE or DECREASE is selected. |
LED Dimming | This output control is used to control the LED dimming from 0-100 percent by 20 percent increments when INCREASE or DECREASE is selected. |
Low Beams | This output control is used to command the low beam headlamps ON or OFF. |
Off LED | This output control is used to command the Off LED ON or OFF. |
Parking Lamps | This output control is used to command the parking lamps ON or OFF. |
Program VIN | This output control is used to program the vehicle identification number (VIN) into the module. |
Setup New IPM / RIM | This output control is used to setup the instrument panel module (IPM) or rear integration module (RIM). |
Smart Beam | This output control is used to enable or disable the smart beam in the rear view mirror. |
Start LED | This output control is used to command the Start LED ON or OFF. |
Stop Lamp | This output control is used to command the stop lamps ON or OFF. |
