GM Service Manual Online
For 1990-2009 cars only

Removal Procedure

    Caution: 

       • Remove the fuel rail assembly carefully in order to prevent damage to the injector electrical connector terminals and the injector spray tips. Support the fuel rail after the fuel rail is removed in order to avoid damaging the fuel rail components.
       • Cap the fittings and plug the holes when servicing the fuel system in order to prevent dirt and other contaminants from entering open pipes and passages.

  1. Relieve the fuel system pressure. Refer to Fuel Pressure Relief.
  2. Remove the front and rear section of the supercharger inlet duct assembly. Refer to Supercharger Inlet Duct Assembly Replacement.
  3. Warning: Wear safety glasses when using compressed air in order to prevent eye injury.

  4. Clean the fuel rail and injector ports on the supercharger with compressed air.

  5. Object Number: 1613998  Size: SH
  6. Disconnect the electrical connectors from the following sensors:
  7. • The supercharger inlet absolute pressure (SCIAP) sensor (1)
    • The barometric pressure (BARO) sensor (2)
    • The manifold absolute pressure (MAP) sensor (3)
  8. Disconnect the vacuum lines from the MAP and SCIAP sensors.
  9. Remove the SCIAP, BARO and MAP sensors with the bracket.

  10. Object Number: 1614613  Size: SH
  11. Partially drain the charge air cooling system. Refer to Charge Air Cooling System Draining and Filling.
  12. Remove the front section of the charge air cooler front manifold assembly (2). It is not necessary to remove the hoses from the manifold pipes. position the manifold with hoses aside to allow for removal of the fuel rail assembly. Refer to Charge Air Cooler Front Manifold Replacement.

  13. Object Number: 1645247  Size: SH
  14. Disconnect the electrical connector from the air inlet temperature 2 sensor and position aside.

  15. Object Number: 1614014  Size: SH
  16. Disconnect the supercharger bypass solenoid valve electrical connector (3) and position the harness aside.
  17. Disconnect the vacuum line from the supercharger actuator valve and position the line aside.

  18. Object Number: 1614622  Size: SH
  19. Disconnect the engine compartment fuel line fitting (4) from the fuel rail. Refer to Metal Collar Quick Connect Fitting Service.

  20. Object Number: 1614623  Size: SH
  21. Disconnect the fuel injector electrical connectors (1, 4, 6, 8) from the left and right side of the engine.

  22. Object Number: 1614611  Size: SH
  23. Open the clip (3) that secures the fuel rail jumper to the front of the supercharger.
  24. Remove the fuel rail attaching studs (2).
  25. Remove the fuel rail assembly (1) from the supercharger.

  26. Object Number: 1655589  Size: SH
  27. Remove the injector lower O-ring seal from the spray tip end of each injector.
  28. Discard the O-ring seals.
  29. Remove the retainers from the fuel injectors if fuel injector removal is necessary.
  30. Remove the fuel injectors from the fuel rail.
  31. Remove the O-ring seals from the fuel injectors. Discard the O-ring seals.

Installation Procedure

    Caution: 

       • Use care when servicing the fuel system components, especially the fuel injector electrical connectors, the fuel injector tips, and the injector O-rings. Plug the inlet and the outlet ports of the fuel rail in order to prevent contamination.
       • Do not use compressed air to clean the fuel rail assembly as this may damage the fuel rail components.
       • Do not immerse the fuel rail assembly in a solvent bath in order to prevent damage to the fuel rail assembly.


    Object Number: 1655589  Size: SH
  1. If the injectors were removed from the fuel rail, lubricate the new fuel injector O-ring seals with clean engine oil.
  2. Install the new fuel injector O-ring seals on to the fuel injectors.
  3. Install the fuel injectors to the fuel rail using new retainer clips.
  4. Ensure that the injectors are aligned by orientating the electrical connectors perpendicular to the crankshaft centerline.
  5. Lubricate and install the new O-ring seals on the spray tip end of each injector.

  6. Object Number: 1614611  Size: SH
  7. Align the fuel injectors and fuel rail to the supercharger assembly.
  8. Carefully press the fuel rail assembly (1) downward until fully seated.
  9. Caution: Refer to Fastener Caution in the Preface section.

  10. Install the fuel rail attaching studs (2) and tighten to 10 N·m (89 lb in).
  11. Install the fuel rail to the clip (3) on the front of the supercharger.

  12. Object Number: 1614623  Size: SH
  13. Connect the fuel injector electrical connectors (1,4,6,8) to the left and right side of the engine.

  14. Object Number: 1614622  Size: SH
  15. Connect the engine compartment fuel line fitting (4) to the fuel rail. Refer to Metal Collar Quick Connect Fitting Service.

  16. Object Number: 1614014  Size: SH
  17. Connect the vacuum line to the supercharger actuator valve.
  18. Connect the supercharger bypass solenoid valve electrical connector (3).

  19. Object Number: 1645247  Size: SH
  20. Connect the electrical connector to the air inlet temperature 2 sensor.

  21. Object Number: 1614613  Size: SH
  22. Install the front section of the charge air cooler front manifold assembly (2). Refer to Charge Air Cooler Front Manifold Replacement.

  23. Object Number: 1613998  Size: SH
  24. Install the SCIAP (1), BARO (2) and MAP (3) sensors with the bracket.
  25. Connect the vacuum lines to the MAP (3) and SCIAP (1) sensors.
  26. Connect the electrical connectors to the following sensors:
  27. • The SCIAP sensor
    • The BARO sensor
    • The MAP sensor
  28. Install the front and rear section of the supercharger inlet duct assembly. Refer to Supercharger Inlet Duct Assembly Replacement.
  29. Install the fuel fill pipe cap.
  30. Fill the charge air cooling system with coolant. Refer to Charge Air Cooling System Draining and Filling.
  31. Check the fuel system for leaks.
  32. Install the engine sight shield. Refer to Intake Manifold Sight Shield Replacement.