DTC P0480 or P0481 with RPO LC3 or LH2

The engine control module (ECM) commands the fans ON in high speed or low speed. In low speed, the fans are configured in series. In high speed, the fans are configured in parallel.

In low speed operation, the ECM applies ground to the coil side of the low speed relay, which is relay 1. Voltage is applied directly to the left cooling fan through the switch side of the low speed relay. The right fan is connected in series to the left fan through the de-energized series/parallel relay so that both fans operate at low speed.

In high speed operation, the ECM applies a ground to the coil side of the low speed relay, which is relay 1, the series/parallel relay, and the high speed relay, which is relay 2. Voltage is applied directly to the right cooling fan through the switch side of the high speed relay. The left cooling fan obtains voltage through the low speed relay and ground through the series/parallel relay.

When the ECM is commanding a fan relay ON, the voltage of the control circuit should be low, near 0 volts. When the ECM is commanding a fan relay OFF, the voltage of the control circuit should be high, near battery voltage.

P0480

The ECM detects an open circuit in the low speed cooling fan relay control circuit.

P0481

Schematic Reference

Connector End View Reference

Description and Operation

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Special Tools Required

J 43244 Relay Puller Pliers

Ignition ON, command each relay ON and OFF with a scan tool. Feel or listen to verify that each relay turns ON and OFF with each command.

1. Ignition OFF, disconnect the S/P fan relay.
2. Connect a 30A fused jumper between the normally-open switch contact terminals R15 and R16 at the S/P fan relay connector in order to complete the fan ground circuit. Leave this jumper in place for the remainder of this procedure.
3. Ignition OFF, disconnect the affected relay.
4. Ignition ON, connect a test lamp between the positive terminal at the battery and the affected relay control circuit terminals listed below:

•	Low speed fan relay terminal R42

•	High speed fan relay terminal R22

5. Command the affected relay ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.

•	Fan 1 relay commands the low speed fan relay

•	Fan 2 and 3 relays command the high speed fan relay

⇒	If the test lamp is always ON, test the relay control circuit for a short to ground. If the circuit tests normal, replace the ECM.

⇒	If the test lamp is always OFF, test the relay control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.

6. Connect a 30A fused jumper between the positive voltage terminal at the battery and the fan voltage supply circuit terminal at the affected relay connectors listed below and verify fan activation.

•	Low speed fan relay terminal R41

•	High speed fan relay terminal R21

⇒	If the fan does not activate, test the fan voltage supply circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the fan.

7. Ignition ON, connect a 30A fused jumper between the relay switch voltage supply circuit terminal and the fan voltage supply circuit terminal at the affected relay connectors listed below and verify fan activation.

•	Low speed fan relay terminal R41

•	High speed fan relay terminal R21

⇒	If the fan does not activate, test the affected relay switch voltage supply circuit for a short to ground or an open/high resistance. If the circuit tests normal and its fuse is open, test all connected components and replace as necessary.

8. Ignition ON, verify that a test lamp illuminates between the affected relay coil voltage supply circuit terminals listed below and ground.

•	Low speed fan relay terminal R39

•	High speed fan relay terminal R19

⇒	If the test lamp does not illuminate, test the affected relay coil voltage supply circuit for a short to ground or an open/high resistance. If the circuit tests normal and its fuse is open, test all connected components and replace as necessary.

9. If all circuits and the ECM test normal, replace the affected relay.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.