Sunroof Window Replacement Rear Vent

1. Move the rear sunroof window to the vent position.
2. Remove the headliner. Refer to Headlining Trim Panel Replacement.




Note: Do not damage the rear vent window seal when removing the screws.

3. Remove the six hinge-to-frame screws (1).
4. Remove the two outer lift cam arm-to-window shouldered screws on each side.
5. Remove the window from the vehicle.

1. Position the rear vent window to the sunroof frame (2).

Caution: Refer to Fastener Caution in the Preface section.

Note: Set the gap from the motor/actuator compartment window to the vent window at 8 mm (0.3 in)

2. Loosely install the six hinge screws.

Tighten
Tighten the screws to 5 N·m (44 lb in).

3. Install the exterior shouldered cam to the window screws.

Tighten
Tighten the screws to 5 N·m (44 lb in).

4. Install the headliner. Refer to Headlining Trim Panel Replacement.
5. Verify the operation of the window.

Sunroof Window Replacement Front

1. Open the front sunroof window approximately 350 mm (13.7 in) to a point just past the air deflector in the full upright position.

Note: Do not damage the sunroof window weatherstrip seal when removing the screws.

2. Depress the weatherstrip seal in order to access the screw locations.



3. Carefully remove the front sunroof to guide the assembly (2) shouldered screws (3).



4. Carefully remove the rear sunroof to rear cam lift arm screws (1).
5. With the aid of an assistant, lift upward from the side edges of the sunroof window.
6. With the aid of an assistant, remove the sunroof window, rearward from the top of the vehicle.

1. With the aid of an assistant, position the front window to the sunroof guide and lift arm assemblies.
2. Align the front and rear holes located on the track arms to the sunroof window attachments.
3. Loosely install the rear screws (1) to each side of the rear cam lift arms.

Caution: Refer to Fastener Caution in the Preface section.




4. Align and install the front shouldered screws (3) to each side of the assembly.

Tighten

•	Tighten the front screws to 5 N·m (44 lb in).

•	Tighten the rear screws to 5 N·m (44 lb in).

5. Cycle the sunroof front window closed then to open.
6. Verify the operation of the front sunroof window.

Sunroof Window Replacement Rear Stationary

1. Remove the headliner. Refer to Headlining Trim Panel Replacement.



2. Remove the screws from the panel bracket to the sunroof frame.



3. Remove the hinge plate to sunroof frame screws.
4. Remove the window panel.

1. Position the window panel to the sunroof frame.



2. Loosely install the screws to the window bracket.



3. Loosely install the screws to the hinge plate sunroof frame

Caution: Refer to Fastener Caution in the Preface section.

4. Verify the panel edge clearances. Refer to Sunroof Window Height and Opening Fit Adjustment.

Tighten
Tighten the window bracket screws to 5 N·m (41 lb in).

Tighten
Tighten the hinge plate sunroof frame screws to 5 N·m (41 lb in).

5. Install the headliner. Refer to Headlining Trim Panel Replacement.

Sunroof Window Replacement Center

1. Pull back the forward sealing strip edge (1) of the center window panel.
2. Remove the 5 attaching screws (2).



3. Tip the window panel (2) upward. Slide the window panel toward the front of the vehicle.
4. Remove the window panel.

1. Tilt the window (2). Slide the window rearward into position.



2. Position the forward weatherstrip (1) under the forward edge of the center window flange (3).
3. Firmly set the center window panel (2) into position.
4. Ensure that the forward and rearward window seams are centered.

Caution: Refer to Fastener Caution in the Preface section.




5. Install the 5 panel attaching screws.

Tighten
Tighten the screws to 5 N·m (44 lb in).