System Software Upgrade-OBD System Improvements (Reprogram Engine Control Module (ECM))

This bulletin provides information about installing new Engine Control Module (ECM) software and calibration on certain 2005-06 Cadillac XLR, SRX and STS model vehicles, equipped with a 4.6L V8 (RPO LH2 - VIN A) engine. The revised calibration includes OBD system improvements that affect the canister purge solenoid (CPS) diagnostics. Install the new calibration and software on all affected vehicles identified in this bulletin as soon as practical, including vehicles in new dealer inventory and any vehicles that return for service, for any reason, during the applicable 8 year/80,000 mile (130,000 km) emission controller warranty coverage period. To verify if an updated calibration is required, refer to the following procedure in this bulletin.

Important: A VIN list of involved vehicles currently in dealer inventory is attached to the Administrative Message (US) or Dealer Communication (Canada) used to release this bulletin.

Do not attempt to order the calibration number from GMSPO. The calibration numbers are programmed into the ECM via a Techline Tech 2 scan tool and the Techline Information System (TIS) 2000 terminal with the calibration update. Use data version 2.0 for 2006 or later, broadcast to dealers on February 5, 2006; (February 8 in Canada) and on TIS CD-ROM version 2.0 / 2006 or later, mailed to dealers beginning February 15, 2006 (February 20 in Canada).

The "Required Field Actions" section of the GM Vehicle Inquiry System (GMVIS) must be checked to determine if a specific vehicle requires this action. If GMVIS indicates that System Software Upgrade 06516 remains ‘open’ and ECM reprogramming has not taken place otherwise after the TIS Broadcast or CD-ROM availability dates identified in this bulletin, reprogram the ECM using a Tech 2 scan tool with the calibration update from Techline Information System (TIS) 2000.

Notice: Before reprogramming, please check the battery condition to prevent a reprogram error of the engine control module (ECM) due to battery discharge. If the vehicle battery is not fully charged, ensure that it is fully charged prior to performing the reprogramming procedure.

The ignition switch must be in the proper position. The Tech 2 prompts you to turn ON the ignition, with the engine OFF. DO NOT change the position of the ignition switch during the programming procedure, unless instructed to do so.

Make certain all tool connections are secure, including the following components and circuits:

DO NOT disturb the tool harnesses while programming. If an interruption occurs during the programming procedure, programming failure or control module damage may occur.

DO NOT turn OFF the ignition if the programming procedure is interrupted or unsuccessful. Ensure that all control module and DLC connections are secure and the TIS terminal operating software is up to date. Attempt to reprogram the control module. If the control module cannot be programmed, replace the control module.

Tech 2 Remote Programming

1. Use the normal "request method" through "Service Programming System" to request information from the vehicle.
2. At the Techline Terminal enter TIS SPS programming system.
3. Select Tech 2 from the "Select Diagnostic Tool" window.
4. Select Reprogram ECU from the "Select Programming Process" window.
5. Select Vehicle from the "Select ECU Location" window.
6. Select Next to go to the "Preparing for Communication" instruction Screen.
7. Select Next to view the "Validate Vehicle ID Number" screen. If the Vehicle ID Number does not appear on the screen, manually insert the VIN into the VIN window of the "Validate Vehicle ID Number" screen.
8. Select Next to view the "Supported Controllers" screen.
9. Select PCM/VCM Powertrain/Vehicle Control Module from "Supported Controllers" window.
10. Select Next to view the "Select Programming Type" window.
11. Select Normal from the "Select Programming Type" window.
12. Select Next to view the "Service Programming System Calibration Selection" screen.
13. Select Next to view "Summary" screen.
14. Verify that current and selected calibration information is displayed on the "Summary" screen.
15. Select Next to download the calibration to the Tech 2.
16. Back at the vehicle enter "Service Programming Systems".
17. Select "Program ECU" and follow on screen instructions.
18. Make sure to turn OFF the ignition for 30 seconds after the "Programming is Complete" screen is displayed. Clear diagnostic trouble codes (DTCs), if required.

For vehicles repaired under the 8 year/80,000 mile (130,000 km) emission controller warranty use: