GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2006 🢒 SRX 🢒 Engine 🢒 Engine Controls - 4.6L (LH2) 🢒 Intake Manifold Replacement

Removal Procedure

    Object Number: 1201072 Size: SH
  1. Remove the cross car brace. Refer to Cross Vehicle Brace Replacement .
  2. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .

    3. Object Number: 928153 Size: SH
  3. Remove the positive crankcase ventilation (PCV) dirty air tube from the camshaft cover. Refer to Positive Crankcase Ventilation Hose/Pipe/Tube Replacement .

    4. Object Number: 928145 Size: SH
  4. Remove the PCV fresh air tube. Refer to Positive Crankcase Ventilation Hose/Pipe/Tube Replacement .

    5. Object Number: 928160 Size: SH
  5. Remove the sight shield bracket nuts.
  6. Remove the sight shield bracket.

    7. Object Number: 887913 Size: SH
  7. Disconnect the left side fuel injector electrical connectors (1) from the fuel injectors (2).

    8. Object Number: 887914 Size: SH
  8. Disconnect the right side fuel injector electrical connectors (1) from the fuel injectors (2).

    9. Object Number: 1239219 Size: SH
  9. Disconnect the evaporative emission (EVAP) purge valve line (2) and electrical connector (1).

    10. Object Number: 1235105 Size: SH
  10. Remove the EVAP line from the retaining feature (2) at the rear of the right head. Position the line aside.
  11. Relieve the fuel system pressure. Refer to Fuel Pressure Relief

    12. Object Number: 1234881 Size: SH
  12. Disconnect the fuel line from the fuel rail (1). Refer to Metal Collar Quick Connect Fitting Service or Plastic Collar Quick Connect Fitting Service .
  13. Remove the fuel line from the retainer at the rear of the right head.

    14. Object Number: 948135 Size: SH
  14. Remove the fasteners attaching the fuel rail to the intake manifold.

    15. Object Number: 1234883 Size: SH
  15. Lift the entire fuel rail and injector assembly from the intake manifold.

    16. Object Number: 1234875 Size: SH
  16. Loosen the plenum duct clamp (1) at the front of the intake manifold.

    17. Object Number: 928175 Size: SH
  17. Loosen the bolts attaching the intake manifold to the cylinder heads.
  18. Remove the intake manifold by using an upward lifting motion at the rear of the manifold assembly.
  19. Inspect the intake manifold. Refer to Intake Manifold Cleaning and Inspection .

Installation Procedure
  1. Transfer the necessary parts when replacing the intake manifold. Refer to Intake Manifold Disassemble and Intake Manifold Assemble .
  2. Lightly grease the inside edge of the rubber plenum duct.

    3. Object Number: 1012862 Size: SH
  3. Ensure that the NEW gaskets are installed to the intake manifold.

    4. Object Number: 928175 Size: SH
  4. Place the intake manifold in position.
  5. Position the front of the intake manifold into the plenum duct.
  6. Position the rear of the intake manifold downward onto the cylinder heads.
  7. Loosely install the 10 bolts attaching the intake manifold to the cylinder heads.

    8. Notice: Refer to Fastener Notice in the Preface section.


    Object Number: 928179 Size: SH
  8. Tighten the intake manifold bolts in sequence (1-10).

    9. Tighten
    Tighten the intake manifold bolts to 10 N·m (89 lb in).

  9. Ensure that the plenum duct is fully attached to the front of the intake manifold.

    10. Tighten
    Tighten the plenum duct clamp to 2.25 N·m (20 lb in).

  10. Lubricate the intake manifold fuel injector bores with light mineral oil, clean engine oil or equivalent. Refer to Adhesives, Fluids, Lubricants, and Sealers for the correct part number.

    11. Object Number: 1234883 Size: SH

    Important: DO NOT force the injectors into position.

  11. Install the entire fuel rail and injector assembly into the intake manifold by pressing the fuel rail and injector simultaneously into the correct position.
  12. Install the bolts attaching the fuel rail to the intake manifold.

    13. Tighten
    Tighten the fuel rail bolts to 10 N·m (89 lb in).


    Object Number: 1234881 Size: SH
  13. Install the fuel line to the retainer at the rear of the right head.
  14. Connect the fuel line to the fuel rail (1). Refer to Metal Collar Quick Connect Fitting Service or Plastic Collar Quick Connect Fitting Service .

    15. Object Number: 1235105 Size: SH
  15. Install the EVAP purge valve line to the retainer (2) at the rear of the right head.

    16. Object Number: 1239219 Size: SH
  16. Install the EVAP purge valve line (2) and electrical connector (1).

    17. Object Number: 887914 Size: SH
  17. Connect the right side fuel injector electrical connectors (1) to the fuel injectors (2).

    18. Object Number: 887913 Size: SH
  18. Connect the left side fuel injector electrical connectors (1) to the fuel injectors (2).

    19. Object Number: 928160 Size: SH
  19. Install the sight shield bracket.
  20. Install the sight shield bracket nuts.

    21. Tighten
    Tighten the sight shield bracket nuts to 10 N·m (89 lb in).


    Object Number: 928145 Size: SH
  21. Install the PCV fresh air tube to the engine.

    22. Object Number: 928153 Size: SH
  22. Install the PCV dirty air tube to the engine.

    23. Object Number: 1201072 Size: SH
  23. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
  24. Install the cross car brace. Refer to Cross Vehicle Brace Replacement .