GM Service Manual Online
For 1990-2009 cars only
Makes 🢒 Cadillac 🢒 2008 🢒 SLS 🢒 Diagnostic Navigation 🢒 Vehicle Diagnostic Information 🢒 DTC B1019

Circuit Description

Inflatable Restraint Sensing and Diagnostic module (SDM) tests the system continuously. When the ignition is ON, the SDM will check the vehicle configuration component installation. If any module is found not programmed after installed to the vehicle or wrong configuration, the SDM will set DTC B 1019. If SDM is replaced, ensure the part installed has the correct part number.

DTC Descriptor

The diagnostic procedure supports the following DTCs:

DTC B1019: System Configuration Error

The vehicle has DTCs including the DTC symptoms. Refer to Diagnostic Procedure Instructions for DTC information.

DTC Symptom

DTC Symptom Descriptor

00

System Configuration Error

Conditions for Running the DTC

Ignition voltage is within normal operating range.

Conditions for Setting the DTC

B1019 00

    • When programming the SDM, option configuration is wrong.
    • The vehicle has installed wrong SDM.
    • Certain module is not configured after being replaced or configured in error.

Action Taken When the DTC Sets
    • The SDM commands the AIR BAG indicator ON via GMLAN serial data communications.
    • The SDM disables all deployments.

Conditions for Clearing the MIL/DTC
    • The vehicle must be installed with correct SDM.
    • Correct components must be installed.
    • All modules are configured correctly.

Diagnostic Aids

The DTC indicates that the SDM installed in the vehicle is not correct or certain module is not configured after being replaced or certain module is incorrectly configured.

Test Description

The following numbers are corresponding to the steps in the diagnostic table.

  1. This step checks if there is current DTC on SDM.

    2.

  2. This step tests if the VIN programmed in the IPM is correct or not.

    3.

  3. This step indicates reprogramming to the IPM is necessary.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

1

Have you conducted Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Important: J-45289 CANdi Module must be used together with the scan tool.

  1. Install the scan tool in order to display the SIR DTCs.
  2. Engine off, ignition on.

Does the scan tool indicate DTC  B1019 as current trouble code?

Go to Step 3

Go to Step 8

3

Using the scan tool check the IPM that is programmed with the VIN. Verify that the IPM is programmed with the correct VIN number with the vehicle VIN plate.

Is the IPM programmed with correct VIN?

Go to Step 6

Go to Step 4

4

Use the scan tool to program the correct VIN into IPM procedure. Refer to Control Module References for replacement, set up, and programming.

Is the reprogramming completed?

Go to Step 5

--

5

Use the scan tool to perform Setup SDM Part Number into IPM under the computer and integration special functions. Refer to Control Module References for replacement, set up, and programming.

Is the reprogramming completed?

Go to Step 8

--

6

Check if the vehicle has new module replaced recently.

Does the vehicle show any sign of new module replaced recently?

Go to Step 7

Go to Step 8

7

Go to the replaced module programming. Refer to Control Module References for replacement, set up, and programming.

Is the reprogramming completed?

Go to Step 8

--

8
  1. Reconnect all SIR components.
  2. Clear away all DTCs with scan tool.
  3. Engine off, ignition off and then on.
  4. Operate the vehicle under conditions when DTC runs as specified in supporting documents.

Does the DTC set again?

Go to Step 9

System OK

9
  1. Turn the ignition switch to OFF position.
  2. Replace the SDM module. Refer to Control Module References for replacement, set up, and programming.

Have you finished the replacement?

Go to Step 10

--

10
  1. Reconnect all SIR components.
  2. Verify all components, connectors and CPAs are correctly installed.
  3. Clear away all DTCs with scan tool.
  4. Engine off, ignition off and then on.
  5. Operate the vehicle under conditions when DTC runs as specified in supporting documents.

Does the DTC set again?

Go to Step 2

System OK