GM Service Manual Online
For 1990-2009 cars only

DTC P0563 3.6L (LY7)

Circuit Description

The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect input can occur when the voltage is out of range. The ECM monitors the system voltage over an extended length of time. If the ECM detects an excessively high system voltage, DTC P0563 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0563 System Voltage High

Conditions for Running the DTC

    • The engine run time is more that 180 seconds.
    • The vehicle speed is more than 5 km/h (3.1 mph).
    • DTC P0563 runs continuously once the above conditions exist for 2 seconds.

Conditions for Setting the DTC

The ECM detects a system voltage more than 18 volts for 4 seconds.

Action Taken When the DTC Sets

    • The ECM will command the charge indicator to be illuminated on the instrument panel cluster (IPC).
    • The ECM will not illuminate the malfunction indicator lamp (MIL).
    • The ECM will store conditions which were present when the DTC set as Failure Records data only.

Conditions for Clearing the DTC

    • The ECM will command the message OFF after one trip in which the diagnostic test has been run and passed.
    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using the scan tool Clear DTC Information function.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Ignition 1 Signal parameter in the Engine Control Module (ECM) data list .

Does the scan tool indicate that the Ignition 1 Signal parameter is less than the specified value?

16 V

Go to Step 4

Go to Step 3

3

Measure the voltage at the battery terminals and compare it with the Ignition 1 Signal parameter in the ECM data list.

Are the battery voltage and Ignition 1 Signal readings different by more than the value specified?

0.5 V

Go to Step 4

Go to Charging System Test

4

Replace the ECM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 5

--

5

  1. Review and record the scan tool Fail Records data.
  2. Clear the DTCs with the scan tool.
  3. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
  4. Using the scan tool, observe the Specific DTC Information for DTC P0563 until the test runs.

Does the scan tool indicate that DTC P0563 failed this ignition?

--

Go to Step 2

System OK

DTC P0563 4.6L (LH2)

Circuit Description

The engine control module (ECM) monitors the system voltage to ensure that the voltage stays within the proper range. Damage to components, and incorrect input can occur when the voltage is out of range. The ECM monitors the system voltage over an extended length of time. If the ECM detects an excessively high system voltage, DTC P0563 will set.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0563 System Voltage High

Conditions for Running the DTC

    • The engine run time is more that 180 seconds.
    • The vehicle speed is more than 5 km/h (3.1 mph).
    • DTC P0563 runs continuously once the above conditions exist for 2 seconds.

Conditions for Setting the DTC

The ECM detects a system voltage more than 18 volts for 4 seconds.

Action Taken When the DTC Sets

    • The ECM will command the charge indicator to be illuminated on the instrument panel cluster (IPC).
    • The ECM will not illuminate the malfunction indicator lamp (MIL).
    • The ECM will store conditions which were present when the DTC set as Failure Records data only.

Conditions for Clearing the DTC

    • The ECM will command the message OFF after one trip in which the diagnostic test has been run and passed.
    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using the scan tool Clear DTC Information function.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Install a scan tool.
  2. Turn ON the ignition, with the engine OFF.
  3. With a scan tool, observe the Ignition 1 Signal parameter in the Engine Control Module (ECM) data list .

Does the scan tool indicate that the Ignition 1 Signal parameter is less than the specified value?

16V

Go to Step 4

Go to Step 3

3

Measure the voltage at the battery terminals and compare it with the Ignition 1 Signal parameter in the ECM data list.

Are the battery voltage and Ignition 1 Signal readings different by more than the value specified?

0.5V

Go to Step 4

Go to Charging System Test

4

Replace the ECM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 5

--

5

  1. Review and record the scan tool Failure Records data.
  2. Clear the DTCs with the scan tool.
  3. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
  4. Using the scan tool, observe the Specific DTC Information for DTC P0563 until the test runs.

Does the scan tool indicate that DTC P0563 failed this ignition cycle?

--

Go to Step 2

System OK