Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptor
DTC 2575 00: Headlamp Control CircuitDiagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Headlamp LO/HID Relay B+ | 1 | 1 | -- | -- |
High Beam Relay B+ | 2 | 2 | -- | -- |
Headlamp Flash to Pass Signal | 4 | 4 | 4 | -- |
Headlamp Dimmer Switch Signal | 4 | 4 | 4 | -- |
Headlamp Low Beam Control | 1 | 1 | 1 | -- |
Headlamp Low Beam Relay Control | 1 | 1 | B2575 00 | -- |
Headlamp Switch Off Control | B257A 00 | 3 | 3 | -- |
Headlamp Switch On Control | B257A 00 | 3 | 3 | -- |
Headlamp High Beam Control | 2 | 2 | 2 | -- |
Headlamp High Beam Relay Control | 2 | 2 | B2580 00 | -- |
Park Lamp Switch On Control | B257A 00 | B257A 00 | 3 | -- |
Headlamp Switch Ground | -- | 2 | -- | -- |
Turn Signal/Multifunction Switch Malfunction | -- | 4 | -- | -- |
| ||||
Circuit/System Description
When the Headlamp and Panel Dimmer Switch is placed in the headlamp ON position, ground is applied to the body control module (BCM) through the headlamp low beam signal circuit. The BCM then applies ground to the HDLP LO/HID Relay control circuit which energizes the low beam relay. With the low beam relay energized, the switch contacts close allowing B+ to flow through the LOW HDLP fuses to the low beam headlamps. Ground for the left headlamp is supplied at G100 and the right headlamp receives ground at G101.
Conditions for Running the DTC
| • | Battery voltage must be between 9-16 volts. |
| • | Headlamps must be ON. |
Conditions for Setting the DTC
DTC B2575 00 will set when the BCM detects a short to voltage in the headlamp low beam relay control circuit.
Actions Taken When the DTC Sets
When DTC B2575 00 is present, the low beam headlamps will not operate.
Conditions for Clearing the DTC
| • | The condition responsible for setting the DTC no longer exists. |
| • | A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred. |
Reference Information
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
- Ignition OFF, disconnect the HDLP LO/HID Relay.
- Connect a test lamp between the control circuit terminal 86 and the B+ circuit terminal 85.
- Ignition ON, command the Low Beam Headlamps ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
- If all circuits test normal, test or replace the HDLP LO/HID Relay.
| ⇒ | If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the BCM. |
| ⇒ | If the test lamp is always OFF, test the control circuit for a short to voltage or open/high resistance. If the circuit tests normal, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
