GM Service Manual Online
For 1990-2009 cars only

Differential Replacement 10.5 Inch Axle

Tools Required

J 24429 Side Bearing Backlash Spanner

Removal Procedure

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
  2. Remove the axle shafts. Refer to Rear Axle Shaft and/or Gasket Replacement .
  3. Remove the rear axle housing cover. Refer to Rear Axle Housing Cover and Gasket Replacement .

  4. Object Number: 667492  Size: SH
  5. Remove the differential bearing adjuster nut retainers.
  6. Caution: Refer to Differential Case Removal Caution in the Preface section.


    Object Number: 667502  Size: SH
  7. Remove the bearing cap bolts.
  8. Remove the bearing caps. Mark the bearing caps left and right.
  9. Loosen the adjusters using the J 24429 .
  10. Notice: Refer to Differential Housing Cover and Gasket Removal Notice in the Preface section.


    Object Number: 667660  Size: SH
  11. Remove the differential assembly.
  12. Remove the bearing cups.
  13. Mark the cups left and right. Place the cups with the bearing caps.

  14. Remove the differential side bearings, if necessary. Refer to Differential Side Bearings Replacement .
  15. Remove the ring gear, if necessary. Refer to Drive Pinion and Ring Gear Replacement .

Installation Procedure

  1. Install the ring gear, if necessary. Refer to Drive Pinion and Ring Gear Replacement .
  2. Install the differential side bearings, if necessary. Refer to Differential Side Bearings Replacement .
  3. Lubricate the differential side bearings with axle lubricant. Use the proper fluid. Refer to Fluid and Lubricant Recommendations in Maintenance and Lubrication.

  4. Object Number: 667660  Size: SH
  5. Place the case, with the bearing cups installed, into the axle housing.
  6. Support the case in order to keep the case from falling out of the axle housing.


    Object Number: 667502  Size: SH
  7. Install the bearing caps and the bolts.
  8. Do not torque the bearing cap bolts at this time.


    Object Number: 694535  Size: SH
  9. Turn the adjusters evenly on each side using the J 24429 until snug against the differential.
  10. Adjust the differential side bearing preload. Refer to Differential Carrier Bearing Preload Adjustment .
  11. Adjust the backlash. Refer to Backlash Adjustment .
  12. Perform a gear tooth contact pattern check. Refer to Gear Tooth Contact Pattern Inspection .
  13. Notice: Refer to Fastener Notice in the Preface section.

  14. Tighten the bearing cap bolts.
  15. Tighten
    Tighten the bearing cap bolts to 185 N·m (136 lb ft).

  16. Install the axle shafts. Refer to Rear Axle Shaft and/or Gasket Replacement .
  17. Install the rear axle housing cover. Refer to Rear Axle Housing Cover and Gasket Replacement .
  18. Fill the axle with the proper lubricant. Refer to Approximate Fluid Capacities and Fluid and Lubricant Recommendations in Maintenance and Lubrication.
  19. Lower the vehicle.

Differential Replacement 8.6, 9.5, 9.5LD Inch Axles

Tools Required

J 24429 Side Bearing Backlash Spanner

Removal Procedure

Important: Group and mark the shims together as originally removed. If you remove or replace the ring and pinion gear set, perform the bearing preload, backlash, and gear tooth contact pattern check in order to ensure proper contact of the gears. If you reinstall or replace the differential carrier without replacing any other component (i.e. pinion and ring gear set, bearings. etc.) then you may reinstall the carrier with the original shims in their original locations. Always perform a gear tooth contact pattern check, even when you remove only the carrier.

  1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle .
  2. Remove the axle shafts. Refer to Rear Axle Shaft Replacement .

  3. Object Number: 667492  Size: SH
  4. Remove the differential bearing adjuster nut lock (9.5/9.5LD inch axle - right side).
  5. Caution: Refer to Differential Case Removal Caution in the Preface section.


    Object Number: 667502  Size: SH
  6. Remove the bearing cap bolts.
  7. Remove the bearing caps. Mark the bearing caps left and right.

  8. Object Number: 156411  Size: SH
  9. For the 8.6 inch axle, install the pinion shaft into the differential case part way and rotate the differential assembly until the pinion shaft contact the top of the axle housing.
  10. Notice: Refer to Differential Housing Cover and Gasket Removal Notice in the Preface section.

  11. For the 8.6 inch axle, rotate the drive pinion clockwise in order to force the differential assembly out of the axle housing.
  12. For the 9.5/9.5LD inch axle, loosen the differential bearing adjuster nut using the J 24429 .
  13. Remove the differential assembly.
  14. Remove the bearing cups, the shims, and the spacers as necessary.
  15. Mark the cups and shims left and right and in the proper order as necessary. Place the cups and the shims with the bearing caps.

  16. Remove the differential side bearings, if necessary. Refer to Differential Side Bearings Replacement .
  17. Remove the ring gear, if necessary. Refer to Drive Pinion and Ring Gear Replacement .

Installation Procedure

  1. Install the ring gear, if necessary. Refer to Drive Pinion and Ring Gear Replacement .
  2. Install the differential side bearings, if necessary. Refer to Differential Side Bearings Replacement .
  3. Lubricate the differential side bearings with axle lubricant. Use the proper fluid. Refer to Fluid and Lubricant Recommendations .

  4. Object Number: 667660  Size: SH
  5. Place the case, with the bearing cups installed, into the axle housing.
  6. Support the case in order to keep the case from falling out of the axle housing.


    Object Number: 667502  Size: SH
  7. Install the bearing caps and the bolts. Do not torque the bearing cap bolts at this time.
  8. Adjust the differential side bearing preload. Refer to Differential Carrier Bearing Preload Adjustment .
  9. Adjust the backlash. Refer to Backlash Adjustment .
  10. Perform a gear tooth contact pattern check. Refer to Gear Tooth Contact Pattern Inspection .
  11. Notice: Refer to Fastener Notice in the Preface section.

  12. Tighten the bearing cap bolts.
  13. Tighten

        • For the 8.6 inch axle, tighten the bearing cap bolts to 75 N·m (55 lb ft).
        • For the 9.5/9.5LD inch axle, tighten the bearing cap bolts to 85 N·m (63 lb ft).
  14. Install the axle shafts. Refer to Rear Axle Shaft Replacement .
  15. Fill the axle with the proper lubricant. Refer to Rear Axle Lubricant Replacement .
  16. Lower the vehicle.