Circuit Description
The 1-2 shift solenoid (SS) valve controls the fluid flow on the 1-2 and the 3-4 shift valves. The 1-2 SS valve is a normally-open exhaust valve that is used with the 2-3 SS in order
to allow 4 different shifting combinations.
When the powertrain control module (PCM) detects a 1-1-4-4 gear ratio, then DTC P0752 sets. DTC P0752 is a type C DTC. For California emissions vehicles and vehicles under 8,600 GVW, DTC P0752
is a type B DTC.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0752 1-2 Shift Solenoid Valve Performance - No Second or Third Gear
Conditions for Running the DTC
| • | No MAF DTC P0101, P0102 or P0103. |
| • | No MAP sensor DTC P0106, P0107, or P0108. |
| • | No TP sensor DTC P0120 or P0220. |
| • | No VSS DTC P0502 or P0503. |
| • | No ISS sensor DTC P0716 or P0717. |
| • | No TCC Stuck ON DTC P0742. |
| • | No Transmission Component Slipping DTC P0894. |
| • | No TFP manual valve position switch DTC P1810. |
| • | No TCC PWM solenoid valve DTC P2761. |
| • | The engine is running for greater than 7 seconds. |
| • | The system voltage is 10-18 volts for 0.5 second. |
| • | Transmission ISS is greater than 7 RPM. |
| • | The transmission OSS is greater than 7 RPM. |
| • | No shift solenoid electrical DTCs P0753 or P0758. |
| • | The throttle angle sensor is greater than 10 percent. |
| • | The engine torque must be between 108 N·m (80 lb ft) and: |
| - | 6.0L: 542 N·m (400 lb ft) |
| - | 8.1L: 881 N·m (650 lb ft) |
| • | No TFP manual valve position switch change within 6 seconds. |
| • | The TFP manual valve position switch indicates D4. |
| • | The transmission fluid temperature (TFT) is 20-130°C (68-266°F). |
| • | The engine vacuum is between 0-105 kPa. |
Conditions for Setting the DTC
| • | The commanded gear equals 2nd and the ratio equals 1st for greater than 2.25 seconds. |
| • | All conditions are met for 5 occurrences. |
Action Taken When the DTC Sets
| • | For California emission equipped vehicles, the PCM illuminates the malfunction indicator lamp (MIL) during the second consecutive trip in which the Conditions for Setting the DTC are met. For Federal emission equipped vehicles, the MIL is
not illuminated. |
| • | The PCM commands maximum line pressure. |
| • | The PCM inhibits 3-2 downshifts above 40 km/h (25 mph). |
| • | The PCM freezes shift adapts. |
| • | The PCM records the operating conditions when the Conditions for Setting the DTC are met. The PCM stores this information as Freeze Frame, California only, and Failure Records, California and Federal. |
| • | The PCM stores the DTC P0752 in PCM history during the second consecutive trip, California, or the first trip, Federal, in which the Conditions for Setting the DTC are met. |
Conditions for Clearing the MIL/DTC
| • | For California emissions, the PCM turns OFF the MIL during the
third consecutive trip in which the diagnostic test runs and passes. |
| • | A scan tool can clear the MIL/DTC. |
| • | For California emissions, the PCM clears the DTC from PCM history
if the vehicle completes 40 warm-up cycles without an emission
related diagnostic fault occurring. |
| • | For Federal emissions, the PCM clears the DTC from PCM history
if the vehicle completes 40 warm-up cycles without a non-emission
related diagnostic fault occurring. |
| • | The PCM cancels the DTC default actions when the fault no longer
exists and the ignition switch is OFF long enough in order to power down
the PCM. |
Diagnostic Aids
| • | Verify that the transmission meets the specifications in the Shift Speed table. Refer to
Shift Speed
. |
| • | DTC P0752 defaults to an elevated line pressure condition which may result in partial TCC apply. This may produce an idle surge that could stall the engine. |
Test Description
The number below refers to the step number on the diagnostic table.
-
This step tests that the PCM commanded all shifts, that all shift solenoid valves responded correctly, but that all the shifts did not occur.
Step
| Action
| Yes
| No
|
1
| Did you perform the Diagnostic System Check - Vehicle?
| Go to
Step 2
| Go to
Diagnostic System Check - Vehicle
|
2
|
- Install a scan tool.
- Turn ON the ignition, with the engine OFF.
Important: Before clearing the DTC, use the scan tool in order to record the Freeze Frame and Failure Records. Using the Clear Info function erases the Freeze Frame and Failure Records from the PCM.
- Record the DTC Freeze Frame and Failure Records.
- Clear the DTC.
- Drive the vehicle in D4 range, accelerating the vehicle, ensuring that the PCM commands 1st, 2nd, 3rd and 4th gears.
Did you detect a 1-1-4-4 shift pattern?
| Go to
Step 3
| Go to
Testing for Intermittent Conditions and Poor Connections
|
3
|
- Inspect the shift solenoid/hydraulic circuit for the following conditions:
| • | 1-2 shift solenoid mechanically stuck ON |
| • | 1-2 shift valve stuck in the applied position |
| • | A cracked 1-2 shift solenoid |
| • | Damaged seals on the shift solenoid valves |
- Clean and inspect the related valves, bores and the valve body for debris or contamination restricting oil flow. Refer to
Control Valve Body Cleaning and Inspection
in Transmission Unit Repair Manual.
Did you find and correct the condition?
| Go to
Step 4
| --
|
4
| Perform the following procedure in order to verify the repair:
- Select DTC.
- Select Clear Info.
- Drive the vehicle in D4 range, holding the throttle at 40% and accelerating to 89 km/h (55 mph), only if traffic and road conditions permit.
- Select Specific DTC.
- Enter DTC P0752.
Has the test run and passed?
| Go to
Step 5
| Go to
Step 2
|
5
| With the scan tool, observe the stored information, capture info and DTC info.
Does the scan tool display any DTCs that you have not diagnosed?
| Go to
Diagnostic Trouble Code (DTC) List - Vehicle
| System OK
|
