GM Service Manual Online
For 1990-2009 cars only

Front Brake Rotor Replacement J55

Tools Required

    • J 41013 Rotor Resurfacing Kit
    • J 42450-A Wheel Hub Resurfacing Kit

Caution: Refer to Brake Dust Caution in the Preface section.

Caution: Two different designs of the front brake rotors and front brake pads are used on this vehicle. Do NOT interchange first design and second design parts, or a loss of braking and personal injury could occur.

Removal Procedure


    Object Number: 370132  Size: SH
  1. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation .
  2. Install a C-clamp over the body of the brake caliper, with the C-clamp ends against the rear of the caliper body and the outboard disc brake pad.
  3. Using the C-clamp, compress the piston into the caliper bore just enough to allow the caliper to slide away from the rotor.
  4. Remove the C-clamp.
  5. Notice: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  6. Remove the brake caliper and the caliper mounting bracket as an assembly from the suspension knuckle and support the assembly with heavy mechanic's wire, or equivalent. Ensure that there is no tension on the hydraulic brake flexible hose. Refer to Front Brake Caliper Bracket Replacement .
  7. Mark the relationship of the rotor to the hub.
  8. Remove the brake rotor.

Installation Procedure

    Important: Whenever the brake rotor has been separated from the hub/axle flange, any rust or contaminants should be cleaned from the hub/axle flange and the brake rotor mating surfaces. Failure to do this may result in excessive assembled lateral runout (LRO) of the brake rotor, which could lead to brake pulsation.


    Object Number: 370132  Size: SH
  1. Use the J 42450-A thoroughly clean any rust or corrosion from the mating surface of the hub/axle flange.
  2. Using the J 41013 thoroughly clean any rust or corrosion from the mating surface and mounting surface of the brake rotor.
  3. Inspect the mating surfaces of the hub/axle flange and the rotor to ensure that there are no foreign particles or debris remaining.
  4. Install the brake rotor to the hub/axle flange. Use the matchmark made prior to removal for proper orientation to the flange.
  5. If the brake rotor was removed and installed as part of a brake system repair, measure the assembled lateral runout (LRO) of the brake rotor to ensure optimum performance of the disc brakes. Refer to Brake Rotor Assembled Lateral Runout Measurement .
  6. If the brake rotor assembled LRO measurement exceeds the specification, bring the LRO to within specifications. Refer to Brake Rotor Assembled Lateral Runout Correction .
  7. Install the brake caliper bracket assembly. Refer to Front Brake Caliper Bracket Replacement .
  8. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation .
  9. Lower the vehicle.
  10. If the brake rotor was refinished or replaced, or if new brake pads were installed, burnish the pads and rotors. Refer to Brake Pad and Rotor Burnishing .

Front Brake Rotor Replacement Without J55

Tools Required

    • J 41013 Rotor Resurfacing Kit
    • J 42450-A Wheel Hub Resurfacing Kit

Caution: Two different designs of the front brake rotors and front brake pads are used on this vehicle. Do NOT interchange first design and second design parts, or a loss of braking and personal injury could occur.

Caution: Refer to Brake Dust Caution in the Preface section.

Removal Procedure

  1. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

  2. Object Number: 654855  Size: SH
  3. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  4. Install a C-clamp over the body of the brake caliper, with the C-clamp ends against the rear of the caliper body and the outboard disc brake pad.
  5. Using the C-clamp, compress the piston into the caliper bore just enough to allow the caliper to slide away from the rotor.
  6. Remove the C-clamp.
  7. Notice: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak.

  8. Remove the brake caliper and the caliper mounting bracket as an assembly from the suspension knuckle and support the assembly with heavy mechanic's wire, or equivalent. Ensure that there is no tension on the hydraulic brake flexible hose. Refer to Front Brake Caliper Bracket Replacement .
  9. Mark the relationship of the rotor to the hub.
  10. Remove the brake rotor.

Installation Procedure

    Important: Whenever the brake rotor has been separated from the hub/axle flange, any rust or contaminants should be cleaned from the hub/axle flange and the brake rotor mating surfaces. Failure to do this may result in excessive assembled lateral runout (LRO) of the brake rotor, which could lead to brake pulsation.


    Object Number: 654855  Size: SH
  1. Use the J 42450-A thoroughly clean any rust or corrosion from the mating surface of the hub/axle flange.
  2. Using the J 41013 thoroughly clean any rust or corrosion from the mating surface and mounting surface of the brake rotor.
  3. Inspect the mating surfaces of the hub/axle flange and the rotor to ensure that there are no foreign particles or debris remaining.
  4. Install the brake rotor to the hub/axle flange. Use the matchmark made prior to removal for proper orientation to the flange.
  5. If the brake rotor was removed and installed as part of a brake system repair, measure the assembled lateral runout (LRO) of the brake rotor to ensure optimum performance of the disc brakes. Refer to Brake Rotor Assembled Lateral Runout Measurement .
  6. If the brake rotor assembled LRO measurement exceeds the specification, bring the LRO to within specifications. Refer to Brake Rotor Assembled Lateral Runout Correction .
  7. Install the brake caliper bracket assembly. Refer to Front Brake Caliper Bracket Replacement .
  8. Install the brake caliper to the brake caliper bracket assembly. Refer to Front Brake Caliper Replacement .
  9. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation in Tires and Wheels.
  10. Lower the vehicle.
  11. If the brake rotor was refinished or replaced, or if new brake pads were installed, burnish the pads and rotors. Refer to Brake Pad and Rotor Burnishing .