GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The system relay is energized when the ignition is ON. The system relay supplies voltage to the solenoid valves and the pump motor. This voltage is referred to as the system voltage.

The electronic brake control module (EBCM) controls each solenoid valve by grounding the solenoid.

The EBCM controls the pump motor by grounding the control circuit. The pump serves 2 purposes:

    • Transfers brake fluid from the brake calipers to the master cylinder reservoir during pressure decrease events
    • Transfers brake fluid from the master cylinder reservoir to the brake calipers during pressure increase events

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC C1217 Pump Motor Shorted to Ground

Conditions for Running the DTC

    • The pump motor has been commanded OFF for 1 second.
    • The system voltage is greater than 9 volts.

Conditions for Setting the DTC

One of the following conditions exists for 0.2 seconds:

    • The voltage across the pump motor is greater than 10.2 volts.
    • The pump motor low side voltage is less than 2.7 volts.

Action Taken When the DTC Sets

If equipped, the following actions occur:

    • The EBCM disables the dynamic rear proportion (DRP)/ABS/traction control system (TCS)/vehicle stability enhancement system (VSES) for the duration of the ignition cycle.
    • The ABS indicator turns ON.
    • The Traction Control indicator turns ON.
    • The driver information center (DIC) displays the Service Stability System message.
    • The EBCM will also set DTC C1248.
    • The red Brake Warning indicator turns ON.

Conditions for Clearing the DTC

    • The condition for the DTC is no longer present and the DTC is cleared with a scan tool.
    • The EBCM automatically clears the history DTC when a current DTC is not detected in 100 consecutive drive cycles.

Diagnostic Aids

    • This DTC determines if there is a short in the pump motor control circuit.
    • The pump motor is integral to the brake pressure modulator valve (BPMV). The pump motor is not serviceable.

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step tests the pump motor circuits of the BPMV for a short to the housing of the BPMV. The wiring from the BPMV to the EBCM should not be repaired.

Step

Action

Values

Yes

No

Schematic Reference: Antilock Brake System Schematics

Connector End View Reference: Antilock Brake System Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Turn OFF the ignition.
  2. Disconnect the electronic brake control module (EBCM) harness connector.
  3. Connect the J 39700 Universal Pinout Box using the J 39700-300 Cable Adapter to the EBCM harness connector only.
  4. Test both ground circuits of the EBCM including the EBCM ground for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 8

Go to Step 3

3

  1. Disconnect the pump motor harness pigtail connector of the brake pressure modulator valve (BPMV).
  2. Measure the resistance between each pump motor control circuit and the housing of the BPMV at the pump motor harness pigtail connector of the BPMV.

Does the resistance measure less than the specified value?

5 ohms

Go to Step 4

Go to Step 5

4

Inspect for poor connections at the pump motor pigtail connector of the BPMV. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 8

Go to Step 6

5

Inspect for poor connections at the harness connector of the EBCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 8

Go to Step 7

6

Replace the BPMV. Refer to Brake Pressure Modulator Valve Replacement .

Did you complete the replacement?

--

Go to Step 8

--

7

Replace the EBCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 8

--

8

  1. Use the scan tool in order to clear the DTCs.
  2. With the scan tool, perform the Automated Test.

Does the DTC reset?

--

Go to Step 2

System OK