GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The powertrain control module (PCM) uses the exhaust gas recirculation (EGR) position sensor to determine the position of the EGR valve. The PCM sends a reference voltage through the 5-volt reference circuit to the EGR position sensor. The PCM provides a voltage return path for the sensor through the low reference circuit. A variable voltage signal, based on the EGR valve position, is sent from the sensor to the PCM through the EGR position sensor signal circuit. If the PCM detects an EGR position sensor voltage that is more than the normal operating range, DTC P0406 sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0406 Exhaust Gas Recirculation (EGR) Position Sensor Circuit High Voltage

Conditions for Running the DTC

    • DTCs P0641 and P0651 are not set.
    • The Ignition 1 Signal parameter is between 11-18 volts.
    • The EGR flow test is not running.
    • DTC P0406 runs continuously once the above conditions are met.

Conditions for Setting the DTC

The EGR position sensor voltage is more than 4.77 volts for more than 350 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Step

Action

Values

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views , Powertrain Control Module Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

--

Go to Step 2

Go to Diagnostic System Check - Vehicle in Vehicle DTC Information

2

  1. Turn ON the ignition.
  2. Observe the EGR Position Sensor parameter.

Is the voltage more than the specified value?

4.77 V

Go to Step 4

Go to Step 3

3

  1. Observe the Freeze Frame/Failure records data for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure records data.

Did the DTC fail this ignition cycle?

--

Go to Step 4

Go to Intermittent Conditions

4

Test for shorted terminals and poor connections at the exhaust gas recirculation (EGR) valve. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 5

5

  1. Disconnect the EGR valve.
  2. Observe the EGR Position parameter on the scan tool.

Is the voltage more than the specified value?

0 V

Go to Step 8

Go to Step 6

6

Measure the voltage between the 5-volt reference circuit of the EGR valve and the low reference circuit of the EGR valve with a DMM.

Is the voltage less than the specified value?

5 V

Go to Step 7

Go to Step 10

7

Repair the open in the low reference circuit of the EGR valve. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 9

8

Repair the short to voltage in the signal circuit of the EGR valve. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you complete the repair?

--

Go to Step 12

Go to Step 9

9

Test for shorted terminals and poor connections at the powertrain control module (PCM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 12

Go to Step 11

10

Replace the EGR valve. Refer to Exhaust Gas Recirculation Valve Replacement .

Did you complete the replacement?

--

Go to Step 12

--

11

Replace the PCM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming.

Did you complete the replacement?

--

Go to Step 12

--

12

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure records data.

Did the DTC fail this ignition?

--

Go to Step 13

Go to Step 2

13

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

--

Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information

System OK