Step | Action | Yes | No |
|---|---|---|---|
Schematic Reference: Fog Lights Schematics Connector End View Reference: Lighting Systems Connector End Views or Computer/Integrating Systems Connector End Views in Computer/Integrating Systems | |||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 |
Do the fog lamps remain illuminated? | Go to Step 3 | Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems |
3 | With a scan tool, observe the Front Fog Lamp Switch parameter in the Instrument Panel Integration Module (IPM) Non-HVAC data list. Does the scan tool indicate that the Fog Lamp Switch parameter is OFF? | Go to Step 4 | Go to Step 7 |
4 |
Does the test lamp illuminate? | Go to Step 5 | Go to Step 10 |
5 |
Did the fog lamps turn OFF? | Go to Step 6 | Go to Step 15 |
6 | Connect a test lamp between the control circuit of the FOG LP relay and the ignition 1 voltage circuit of the FOG LP relay coil. Does the test lamp illuminate? | Go to Step 8 | Go to Step 11 |
7 |
Does the scan tool indicate that the Front Fog Lamp Switch parameter is OFF? | Go to Step 12 | Go to Step 9 |
8 | Test the control circuit of the FOG LP relay for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 14 |
9 | Test the front fog lamp switch signal circuit for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 13 |
10 | Test the front fog lamp switch signal circuit for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 13 |
11 | Inspect for poor connections at the FOG LP relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 16 |
12 | Inspect for poor connections at the harness connector of the headlamp switch. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 17 |
13 | Inspect for poor connections at the IPM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 18 |
14 | Inspect for poor connections at the dash integration module (DIM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | Go to Step 20 | Go to Step 19 |
15 | Repair a short to voltage in the fog lamp supply voltage circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | Go to Step 20 | -- |
16 | Replace the FOG LP relay. Refer to Relay Replacement in Wiring Systems. Did you complete the replacement? | Go to Step 20 | -- |
17 | Replace the headlamp switch. Refer to Headlamp Switch Replacement . Did you complete the replacement? | Go to Step 20 | -- |
18 | Replace the IPM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 20 | -- |
19 | Replace the DIM. Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | Go to Step 20 | -- |
20 | Operate the system in order to verify the repair. Did you correct the condition? | System OK | Go to Step 2 |
