DTC P1101. Cadillac DeVille 2004

For 1990-2009 cars only

Makes 🢒 Cadillac 🢒 2004 🢒 DeVille 🢒 Engine 🢒 Engine Controls - 4.6L 🢒 DTC P1101

Circuit Description

The intake flow rationality diagnostic provides the within-range rationality check for the mass air flow (MAF), manifold absolute pressure (MAP), and the throttle position (TP) sensor. This is an explicit model-based diagnostic containing 3 separate models for the intake system.

•	One model, the throttle model, describes the flow through the throttle body and is used to estimate the MAF through the throttle body as a function of barometric pressure (BARO), TP, intake air temperature (IAT), and estimated MAP.

•

Another model, the first intake manifold model, describes the intake manifold and is used to estimate MAP as a function of the MAF into the manifold from the throttle body and from the exhaust gas recirculation (EGR) valve, and the MAF out of the manifold caused by engine pumping. The flow into the manifold from the throttle uses the MAF estimate calculated from the above throttle model.

•	The third model is the second intake manifold model and is identical to the first intake manifold model except that the MAF sensor measurement is used instead of the throttle model estimate for the throttle air input.

•	Finally, a fourth model is created from the combination and additional calculations of the throttle model and the first intake manifold model.

The estimates of MAF and MAP obtained from this system of models and calculations are then compared to the actual measured values from the MAF, MAP, and the TP sensor and to each other to determine the appropriate DTC to fail. The following table illustrates the possible failure combinations and the resulting DTC or DTCs.

Throttle Model	First Intake Manifold Model	Second Intake Manifold Model	Fourth Model	DTCs Passed	DTCs Failed
X	X	Pass	Pass	P0101 P0106 P0121 P1101	None
Pass	Pass	Failed	Pass	P0101 P0106 P0121 P1101	None
Failed	Pass	Failed	Pass	P0106 P0121 P1101	P0101
Pass	Failed	Failed	Pass	P0101 P0121 P1101	P0106
Failed	Failed	Failed	Pass	P0121 P1101	P0101 P0106
X	X	Pass	Failed	P0101 P0106 P1101	P0121
Pass	Pass	Failed	Failed	P0101 P0106 P0121 P1101	None
Failed	Pass	Failed	Failed	P0101 P0106 P0121	P1101
X	Failed	Failed	Failed	P0101 P0106 P0121	P1101

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P1101 Intake Air Flow System Performance

Conditions for Running the DTC

•	DTCs P0102, P0103, P0107, P0108, P0112, P0113, P0117, P0118, P0335, P0336, P0385, P0386, P0401, P0405, P1404 are not set.

•	The engine speed is between 500-6,700 RPM.

•	The IAT Sensor parameter is between -7 and +60°C (19-140°F).

•	The ECT Sensor parameter is between 70-121°C (158-250°F).

•	This DTC runs on a 12.5 ms loop.

•	This DTC runs continuously within the enabling conditions.

Conditions for Setting the DTC

The powertrain control module (PCM) detects that the actual measured airflow from MAF, MAP, EGR, and TP is not within range of the calculated airflow that is derived from the system of models for more than 0.5 second.

Action Taken When the DTC Sets

•	The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.

•

The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

•	The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail.

•	A current DTC, Last Test Failed, clears when the diagnostic runs and passes.

•	A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.

•	Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

•	Any condition that can cause the MAF, MAP, EGR, and TP sensors to be shifted in value at the same time will cause this DTC to set.

•

A wide open throttle (WOT) acceleration from a stop should cause the MAF sensor parameter on the scan tool to increase rapidly. This increase should be from 3-10 g/s at idle to 220 g/s or more at the time of the 1-2 shift. If the increase is not observed, inspect for a restriction in the induction system or the exhaust system.

•	A skewed or stuck engine coolant temperature (ECT) or IAT sensor will cause the calculated models to be inaccurate and may cause this DTC to run when it shouldn't.

•	A steady or intermittent high resistance of 15 ohms or more on the ignition 1 voltage circuit will cause the MAF sensor values to be skewed high by up to 60 g/s, and may cause this DTC to set. A high resistance will cause a drivability concern before this DTC sets.

•

The barometric pressure (BARO) that is used to calculate the air flow models is initially based on the MAP sensor at key ON. When the engine is running the BARO value is continually updated near WOT. A skewed MAP sensor will cause the calculated MAF value to be inaccurate and may result in a no start condition. The value shown for the MAP sensor parameter varies with the altitude. With the ignition ON and the engine OFF, 101 kPa is the approximate value near sea level. This value will decrease by approximately 3 kPa for every 305 meters (1,000 feet) of altitude.

•	A high resistance on the low reference circuit of the MAP sensor and the TP sensor at the same time may cause this DTC to set.

•	If the condition is intermittent, refer to Inducing Intermittent Fault Conditions in Wiring Systems and Intermittent Conditions .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

This step will determine if any mechanical faults have caused this DTC to set.

This voltage drop test will determine if high resistance has caused this DTC to set.

This step verifies the voltage signal from the PCM to the MAF sensor connector.

This step will determine if the PCM can accurately process the frequency signal that it receives from the MAF sensor.

This step will determine if an abnormal resistance of less than 1,150 ohms has skewed the MAF sensor frequency signal.

Step

Action

Values

Yes

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Controls Connector End Views or Powertrain Control Module Connector End Views

Did you perform the Diagnostic System Check-Engine Controls?

Go to Step 2

Go to Diagnostic System Check - Engine Controls

Important: This Diagnostic Routine may have to be followed more than once. This is because a shift in multiple values cause DTC P1101 to set.

Attempt to start the engine.

Does the engine start?

Go to Step 3

Go to Step 4

Observe the Freeze Frame/Failure Records for this DTC.
Turn OFF the ignition for 60 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 4

Go to Diagnostic Aids

Turn OFF the ignition.
Inspect for the following conditions:

•	A restricted or collapsed air intake duct

•	A misaligned air intake duct

•	A dirty or deteriorating air filter element

•	Any objects blocking the air inlet screen of the mass air flow (MAF)/intake air temperature (IAT) sensor

•	Any contamination or debris on the sensing elements of the MAF sensor

•	Any water intrusion in the induction system

•	Any vacuum leak downstream of the MAF sensor

•	An intake manifold leak

•	An engine misfire--Refer to DTC P0300 .

•	A manifold absolute pressure (MAP) sensor seal that is missing or damaged

•	A skewed or stuck engine coolant temperature (ECT) or IAT sensor--Refer to Temperature Versus Resistance .

•	A damaged exhaust gas recirculation (EGR) valve

•	A leaking EGR valve

•	Any type of restriction in the exhaust system--Refer to Restricted Exhaust in Engine Exhaust.

Did you find and correct the condition?

Go to Step 24

Go to Step 5

Important:: The Altitude vs. Barometric Pressure table indicates a pressure range for a given altitude under normal weather conditions. Weather conditions consisting of very low or very high pressure and/or temperature may cause a reading to be slightly out of range.

Accurately determine the altitude.
Turn ON the ignition, with the engine OFF.
Observe the MAP Sensor kPa parameter with a scan tool.
The MAP sensor pressure should be within the specified range for your altitude. Refer to Altitude Versus Barometric Pressure .

Is the MAP sensor pressure within the specified range as indicated on the Altitude vs. Barometric pressure table?

Go to Step 6

Go to DTC P0106

Start the engine.
Turn OFF all lights and accessories.
Allow the engine to reach operating temperature.
Observe the MAP Sensor parameter with a scan tool.

Is the MAP Sensor parameter within the specified range?

19-40 kPa

Go to Step 7

Go to DTC P0106

Idle the engine.
Take a snapshot of the Engine Data list while performing the following action. Refer to Scan Tool Snapshot Procedure in Wiring Systems.
Increase the engine speed slowly to 3,000 RPM and then slowly back to idle.
Exit from the snapshot and review the data.
Observe the MAP Sensor kPa parameter frame by frame with a scan tool.

Does the MAP Sensor parameter change smoothly and gradually through the specified range of the test?

Go to Step 8

Go to DTC P0106

Turn OFF the ignition for 30 seconds.
Turn ON the ignition, with the engine OFF.
Observe The TP Sensor parameter at closed throttle with a scan tool.
Depress the accelerator pedal completely.
Observe The TP Sensor parameter at wide open throttle (WOT) with a scan tool.

Does the TP Sensor parameter change from the first value to the second value?

0-100%

Go to Step 9

Go to DTC P0121

Take a snapshot of the Engine Data list while performing the following action. Refer to Scan Tool Snapshot Procedure in Wiring Systems.
Slowly depress the accelerator pedal to WOT and then slowly release the pedal to closed throttle.
Exit from the snapshot and review the data frame by frame.

Does the TP Sensor parameter change smoothly and completely from the first value to the second value and then back to the first value?

0-100%

Go to Step 10

Go to DTC P0121

Inspect the throttle body and the throttle plate for the following conditions:

•	Any damage

•	Any deposits or restriction that could affect the air flow through it

•	Any missing parts

•	A throttle valve that is not fully closed when the accelerator pedal is fully released

•	A throttle valve that is not fully open when the accelerator pedal is fully depressed

Did you find and correct the condition?

Go to Step 24

Go to Step 11

Start the engine.
Idle the engine.
Observe the EGR Position Sensor parameter with a scan tool.

Is the EGR Position Sensor parameter at the specified value?

Go to Step 12

Go to DTC P0404

Turn OFF the ignition.
Turn ON the ignition, with the engine OFF.
Measure the battery voltage with a DMM.
Disconnect the MAF sensor.
Connect a test lamp between the ignition 1 voltage circuit of the MAF sensor and a good ground. Refer to Probing Electrical Connectors in Wiring Systems.
Connect the DMM to the probe of the test lamp and a good ground. Refer to Measuring Voltage Drop in Wiring Systems.

Is the voltage within 0.50 volts of the specified value?

B+

Go to Step 13

Go to Step 20

Important: All electrical components and accessories must be turned OFF.

Turn OFF the ignition for 60 seconds to allow the control modules to power down.
Measure the resistance from the ground circuit of the MAF sensor to a good ground with a DMM. Refer to Circuit Testing in Wiring Systems.

Is the resistance less than the specified value?

5 ohms

Go to Step 14

Go to Step 21

Turn ON the ignition, with the engine OFF.
Measure the voltage from the signal circuit of the MAF sensor to a good ground with a DMM. Refer to Circuit Testing in Wiring Systems.

Is the voltage within the specified range?

4.9-5.2 V

Go to Step 15

Go to Step 17

Turn OFF the ignition.
Connect the voltage supply and the ground lead of the J 38522 Variable Signal Generator to the vehicle.
Connect the red lead of the J 38522 to the signal circuit of the MAF sensor. Refer to Probing Electrical Connectors in Wiring Systems.
Set the Duty Cycle switch of the J 38522 to Normal.
Set the Frequency switch of the J 38522 to 5 K.
Set the Signal switch of the J 38522 to 5 V.
Start the engine.
Observe the MAF Sensor parameter with a scan tool.

Is the MAF Sensor parameter within the specified range?

4,950-5,025 Hz

Go to Step 16

Go to Step 17

Important: The J 38522 is able to overcome an abnormal resistance on the signal circuit of up to 1,150 ohms. The MAF sensor will not be able to overcome a resistance this high.

Turn OFF the ignition.
Disconnect the powertrain control module (PCM).
Test the MAF sensor signal circuit for a high resistance.

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 18

Turn OFF the ignition.
Disconnect the PCM.
Test the MAF sensor signal circuit for the following conditions:

•	A high resistance

•	An intermittent open circuit

•	A high resistance short to ground

Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 19

Test for an intermittent and for a poor connection at the MAF sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs and Repairing Connector Terminals in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 22

Test for an intermittent and for a poor connection at the PCM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs and Repairing Connector Terminals in Wiring Systems.

Did you find and correct the condition?

Go to Step 24

Go to Step 23

Repair the high resistance or the intermittent open in the MAF sensor ignition 1 voltage circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 24

Repair the high resistance or the intermittent open in the MAF sensor ground circuit. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 24

Replace the MAF/IAT sensor. Refer to Mass Airflow Sensor/Intake Air Temperature Sensor Replacement .

Did you complete the replacement?

Go to Step 24

Replace the PCM. Refer to Powertrain Control Module Replacement .

Did you complete the replacement?

Go to Step 24

Important: This Diagnostic Routine may have to be followed more than once. This is because a shift in multiple values cause P1101 to set.

Clear the DTCs with a scan tool.
Turn OFF the ignition for 60 seconds.
Start the engine.
Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 2

Go to Step 25

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

Go to Diagnostic Trouble Code (DTC) List

System OK