Linear Shift Assembly - Assemble - Off Vehicle Power Tilt\\Telescope-Column Shift
Tools Required
J 41396 Park Lock
Cable Pliers
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the linear
shift assembly and secure using 3 flat head 6 lobed socket tap
screws.
Tighten
Tighten the screws to 10 N·m (89 lb in).
- The lock cylinder should
be in the OFF or LOCK position.
Important: The locking tab at the end of the park lock cable assembly (1)
must be secure in the lock module assembly.
- Connect the park lock cable assembly (1).
- Adjust the park lock cable
assembly.
4.1. | Use the gear shift lever to put the column in the park position. |
4.2. | Put the ignition switch in the OFF or LOCK position. Remove the
key. |
4.3. | Unlock the adjuster ring on the park lock cable assembly with J 41396
. |
4.4. | Pull on the cable until the park lock latch contacts the gear
shift lever. Release the cable. |
4.5. | Lock the adjuster ring securely in place on the park lock cable
assembly with J 41396
. |
- Inspect the park lock cable assembly.
5.1. | Put the lock cylinder in the OFF or LOCK position. The gear shift
lever should not be able to shift out of the park position. |
5.2. | Turn the key to the run position and put the gear shift lever
in the neutral position. |
5.3. | With the gear shift lever in the neutral position the lock cylinder
should not be able to go into the OFF or LOCK position. |
5.4. | Put the gear shift lever in the park position. |
5.5. | Put the lock cylinder in the OFF or LOCK position and then remove
the key. |
- Install the automatic transmission shift lock control assembly
only. Refer to
Automatic Transmission Shift Lock Control Assemble - Off Vehicle
.
- Install the shift lever. Refer to
Shift Lever - Assemble - Off Vehicle
.
Linear Shift Assembly - Assemble - Off Vehicle Manual Tilt, Column Shift
Tools Required
J 41396 Park Lock
Cable Pliers
Notice: Use the correct fastener in the correct location. Replacement fasteners
must be the correct part number for that application. Fasteners requiring
replacement or fasteners requiring the use of thread locking compound or sealant
are identified in the service procedure. Do not use paints, lubricants, or
corrosion inhibitors on fasteners or fastener joint surfaces unless specified.
These coatings affect fastener torque and joint clamping force and may damage
the fastener. Use the correct tightening sequence and specifications when
installing fasteners in order to avoid damage to parts and systems.
- Install the cable
support bracket (4) onto the steering column and secure using the 3 flat
head screws (3).
Tighten
Tighten the 3 flat head screws to 3.5 N·m (32 lb
in)
- Install the linear shift assembly and secure using the 3 flat
head 6 lobed socket tap screws.
Tighten
Tighten the 3 6-lobed socket tap screws to 5 N·m
(44 lb in).
- The lock cylinder should
be in the OFF or LOCK position.
Important: The locking tab at the end of the park lock cable assembly (1)
must be secure in the lock module assembly.
- Connect the park lock cable assembly (1).
- Adjust the park lock cable
assembly using the following steps:
5.1. | Use the gear shift lever to put the column in the park position. |
5.2. | Put the ignition switch in the OFF or LOCK position. Remove the
key. |
5.3. | Unlock the adjuster ring on the park lock cable assembly with J 41396
. |
5.4. | Pull on the cable until the park lock latch contacts the gear
shift lever. Release the cable. |
5.5. | Lock the adjuster ring securely in place on the park lock cable
assembly with J 41396
. |
- Inspect the park lock cable assembly using the following steps:
6.1. | Put the lock cylinder in the OFF or LOCK position. The gear shift
lever should not be able to shift out of the park position. |
6.2. | Turn the key to the run position and put the gear shift lever
in the neutral position. |
6.3. | With the gear shift lever in the neutral position the lock cylinder
should not be able to go into the OFF or LOCK position. |
6.4. | Put the gear shift lever in the park position. |
6.5. | Put the lock cylinder in the OFF or LOCK position and then remove
the key. |
- Install the automatic transmission shift lock control and bracket
only. Refer to
Automatic Transmission Shift Lock Control Assemble - Off Vehicle
.
- Install the shift lever. Refer to
Shift Lever - Assemble - Off Vehicle
.