Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle Power Tilt\\Telescope-Column Shift
- Install the ignition and key alarm switch assembly (2) and secure by using 2 tapping screws (3).
- Install the ignition and key alarm connector (1) onto the lock module assembly (4).
- Install the green connector into the bottom of the ignition and key alarm switch assembly (2).
- Put the lead in the clip located on the side of the ignition and key alarm switch assembly (2).
- Install the coded key controller (2) onto the lock module assembly (1).
- Connect the coded key controller.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
- Install the steering column lock cylinder set. Refer to Ignition Lock Cylinder Replacement - On Vehicle .
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Tighten
Tighten the screws to 1.5 N·m (13 lb in).
Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle Power Tilt and Telescope, Floor Shift
- Install the ignition and key alarm switch assembly (2) and secure by using 2 tapping screws (3).
- Install the ignition and key alarm connector (1) onto the lock module assembly (4).
- Install the green connector into the bottom of the ignition and key alarm switch assembly (2).
- Put the lead in the clip located on the side of the ignition and key alarm switch assembly (2).
- Install the coded key controller connector (2) onto the lock module assembly (1).
- Connect the coded key controller connector.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
- Install the steering column lock cylinder set. Refer to Ignition Lock Cylinder Replacement - On Vehicle .
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Important: The lower tapping screw also attaches the electric park lock.
Tighten
Tighten the screws to 1.5 N·m (13 lb in).
Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle Manual Tilt, Floor Shift
- Install the ignition and key alarm switch assembly (2) and secure by using the 2 tapping screws (3).
- Install the key alarm connector (1) onto the lock module assembly (4).
- Install the connector into the bottom of the ignition and key alarm switch assembly (2).
- Put the lead in the clip located on the side of the ignition and key alarm switch assembly (2).
- Install the coded key controller (2) onto the lock module assembly (1).
- Connect the coded key controller connector.
- Install the steering column lock cylinder set. Refer to Ignition Lock Cylinder Replacement - On Vehicle .
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Important: The lower tappng screw also attaches the electric park lock.
Tighten
Tighten the 2 tapping screws to 1.5 N·m (13 lb in).
Ignition and Key Alarm Switch Assembly - Assemble - Off Vehicle Manual Tilt, Column Shift
- Install the ignition and key alarm switch assembly (2) and secure by using the 2 tapping screws (3).
- Install the key alarm connector (1) onto the lock module assembly (4).
- Install the connector(s) into the bottom of the ignition and key alarm switch assembly (2).
- Put the lead in the clip located on the side of the ignition and key alarm switch assembly (2).
- Install the coded key controller (2) onto the lock module assembly (1).
- Connect the coded key controller connector.
- Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .
- Install the steering column lock cylinder set. Refer to Ignition Lock Cylinder Replacement - On Vehicle .
Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.
Tighten
Tighten the 2 tapping screws to 1.5 N·m (13 lb in).
