Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Power Tilt\\Telescope-Column Shift

1. Install the turn signal and multifunction switch assembly (3) onto the steering column.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the lower pan head tapping screw (2) first.

Tighten
Tighten the lower pan head tapping screw to 2.5 N·m (22 lb in).

3. Install the top pan head tapping screw (1) last.

Tighten
Tighten the top pan head tapping screw to 2.5 N·m (22 lb in).

4. Connect the 3 connectors to the turn signal and multifunction switch assembly (3).
5. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .

Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Power Tilt\\Telescope, Floor Shift

1. Install the turn signal and multifunction switch assembly (3) onto the steering column.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the lower pan head tapping screw (2) first.

Tighten
Tighten the lower pan head tapping screw to 2.5 N·m (22 lb in).

3. Install the top pan head tapping screw (1) last.

Tighten
Tighten the top pan head tapping screw to 2.5 N·m (22 lb in).

4. Connect the 3 connectors to the turn signal and multifunction switch assembly (3).
5. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .

Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Manual Tilt, Floor Shift

1. Install the turn signal and multifunction switch assembly (3) onto the steering column.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the lower pan head tapping screw (2) first.

Tighten
Tighten the lower pan head tapping screw to 2.5 N·m (22 lb in).

3. Install the top pan head tapping screw (1) last.

Tighten
Tighten the top pan head tapping screw to 2.5 N·m (22 lb in).

4. Connect the connector(s) to the turn signal and multifunction switch assembly (3).
5. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .

Turn Signal and Multifunction Switch Assembly - Assemble - Off Vehicle Manual Tilt, Column Shift

1. Install the turn signal and multifunction switch assembly (3) onto the steering column.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

2. Install the lower pan head tapping screw (2) first.

Tighten
Tighten the lower pan head tapping screw to 2.5 N·m (22 lb in).

3. Install the top pan head tapping screw (1) last.

Tighten
Tighten the top pan head tapping screw to 2.5 N·m (22 lb in).

4. Connect the connector(s) to the turn signal and multifunction switch assembly (3).
5. Install the upper and lower trim covers. Refer to Steering Column Trim Covers - Assemble - Off Vehicle .