Tools Required

J 39061 Converter Seal Installer

1. Inspect the drive sprocket support for the following:

•	Spline damage

•	Journal damage

•	Bushing damage

•	Blocked converter drain holes




2. Remove the six 8-mm drive sprocket support bolts (404).
3. Remove the drive sprocket support (400) and remove the drive sprocket support seal (405).



4. Place the drive sprocket support (400) in a soft jaw vise. Use a wedge-shaped chisel in order to remove the converter helix seal (403).



5. Install a new drive sprocket support seal (405). Install the drive sprocket support (400) into the case.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

6. Attach the six 8-mm bolts (404).

Tighten
Using a star pattern, tighten the bolts to 11-13 N·m (8.0-9.5 lb ft).




7. Use theJ 39061 in order to install the new converter helix seal (403).



8. Inspect the wiring harness for the following:

•	Cut or pinched wires

•	Cut wire insulation

•	Bent or broken connectors

9. Install the wiring harness into the case, with the notch going toward the inside of the case. Make sure that the harness snaps into place at the pass through connector (12). Insert the remainder of the harness into the valleys of the case housing.



10. Install the input speed sensor (14) and its bolt (15).
11. Install the input speed sensor wire harness bracket to the center of the case. Install its bolt (15).



12. Inspect the actuator park lock sleeve for excessive wear. Inspect the actuator rod (21) for a cracked end, a bent rod, or a broken spring.



13. Inspect the threads on the manual shaft (16). Inspect the machined area of the shaft, where the seal rides, for nicks and burrs.



14. Install the new manual shaft seal (20) onto the manual shaft.
15. Place the manual shaft (16) through the case.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

16. Align the notch on the input speed sensor wire harness bracket to the groove on the manual shaft. Tighten its bolt (15).

Tighten
Tighten the bolts to 11-13 N·m (8.0-9.5 lb ft).

17. Seat the manual shaft seal (20) with the appropriate socket.



18. Attach the new detent lever (17), the actuator rod (21) and nut (18) to the manual shaft. Hold the detent lever stationary with a screwdriver in order to prevent bending of the actuator rod. Slide the actuator rod into the actuator park lock sleeve.

Tighten
Tighten the nut to 27-34 N·m (20-25 lb ft).

19. Install the detent roller assembly washer (26), the pivot arm, and the sleeves. Start the pivot bolt by hand.

Tighten
Tighten the pivot bolt to 8-14 N·m (6-10 lb ft).

20. Install the detent return spring (27) to the detent roller assembly and manual shaft. Install the spring with the small hook end around of the top of the manual shaft.