GM Service Manual Online
For 1990-2009 cars only

DTC Descriptors

DTC U0100 00: Lost Communication With Engine/Powertrain Control Module (ECM/PCM)

DTC U0101 00: Lost Communication With Transmission Control Module (TCM)

DTC U0104 00: Lost Communication With Cruise Control Module

DTC U0121 00: Lost Communication With Electronic Brake Control Module (EBCM)

DTC U0122 00: Lost Communication With Vehicle Dynamics Control Module

DTC U0132 00: Lost Communication With Ride Level Control Module

DTC U0140 00: Lost Communication With Body Control Module (BCM)

DTC U0151 00: Lost Communication With Restraints Control Module

DTC U0155 00: Lost Communication With Instrument Panel Cluster (IPC) Control Module

DTC U0159 00: Lost Communication With Parking Assist Control Module A

DTC U0164 00: Lost Communication With HVAC Control Module

DTC U0168 00: Lost Communication With Vehicle Theft Deterrent (VTD) Control Module

DTC U0170 00: Lost Communication With Passenger Presence System (PPS)

DTC U0184 00: Lost Communication With Radio

DTC U0186 00: Lost Communication With Audio Amplifier

DTC U0194 00: Lost Communication With Digital Radio Receiver (DRR)

DTC U0198 00: Lost Communication With Communication Interface Module (OnStar®)

DTC U0199 00: Lost Communication With Door control Module A

DTC U0200 00: Lost Communication With Door control Module B

DTC U0209 00: Lost Communication With Heated Seat Module (HSM)

DTC U0214 00: Lost Communication With Remote Function Actuation (RFA)

DTC U0241 00: Lost Communication With Headlamp Control Module A

Diagnostic Fault Information

Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Low speed GMLAN serial data

1

U0100- U0299

1

--

Battery positive voltage circuits

U0100- U0299

U0100- U0299

--

--

Ignition voltage circuits

U0100- U0299

U0100- U0299

--

--

Module ground circuits

U0100- U0299

U0100- U0299

--

--

Accessory Wake Up Serial Data

U1814

U0100- U0299

--

--

High Speed GMLAN Serial Data Wake Up

U2099

U0100- U0299

--

--

1. Scan Tool Does Not Communicate with Low Speed GMLAN Device

Circuit/System Description

Modules connected to the high and low speed GMLAN serial data circuits monitor for serial data communications during normal vehicle operation. Operating information and commands are exchanged among the modules. The modules have prerecorded information about what messages are needed to be exchanged on the serial data circuits, for each virtual network. The messages are supervised and also, some periodic messages are used by the receiver module as an availability indication of the transmitter module. Each message contains the identification number of the transmitter module.

The body control module (BCM) activates the high speed GMLAN serial data wake up and the accessory wake up serial data circuits by applying voltage when the ignition key is in ACC, ON or START. The high speed GMLAN serial data wake up circuit wakes up the electronic brake control module (EBCM) for bus communication and the accessory wake up serial data circuit wakes up the engine control module (ECM) and transmission control module (TCM)

Conditions for Running the DTC

    • The system voltage is between 9-16 volts.
    • The vehicle power mode requires serial data communication to occur.

Conditions for Setting the DTC

A supervised periodic message that includes the transmitter module availability has not been received.

Action Taken When the DTC Sets

The module uses a default value for the missing parameters.

Conditions for Clearing the DTC

    • A current DTC clears when the malfunction is no longer present.
    • A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.

Diagnostic Aids

    • Use the DTC Descriptor list above to determine the module which is not communicating.
    • If there are multiple non-communicating modules choose the one closest to the data link connector (DLC).
    • Use Data Link References to determine if the module uses high or low speed GMLAN serial data communications
    • Some modules may not have internal protection for specific voltage outputs and may open a battery positive voltage or ignition voltage source fuse. If a voltage input fuse is open and no short is found in that circuit, ensure that no module output voltage circuit is shorted to ground before replacing the module.
    • This diagnostic can be used for any module that should communicate with high or low speed GMLAN serial data providing the vehicle is equipped with the option that uses that module.

Reference Information

Schematic Reference

    •  Data Link Connector Schematics
    •  Control Module References

Connector End View Reference

Master Electrical Component List

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Circuit/System Testing

    Important: If more than one module is not communicating use Data Link Connector Schematics to determine which module is closest to the DLC. Start diagnostics with that module.

  1. Using the DTC Descriptor and Diagnostic Aids above, determine the module that is not communicating that should be tested.
  2. Ignition OFF, disconnect the harness connector of the module that is not communicating.
  3. Important: Only the high speed GMLAN modules have a wired serial data wake up circuit. Refer to the module schematics to identify which modules have a wake up circuit. If the module that is not communicating does not have a serial data wake up circuit, proceed to step 4.

  4. Ignition ON, verify that a test lamp illuminates between the high speed GMLAN serial data wake up circuit OR the accessory wake up serial data circuit and ground.
  5. If the test lamp does not illuminate, test the circuit for an open/high resistance. If the circuits test normal, replace the BCM.
  6. Ignition ON, verify that a test lamp illuminates between all battery positive voltage circuits and ground.
  7. If the test lamp does not illuminate, repair the circuit for a short to ground or an open/high resistance. If the circuit fuse is open, also test the positive voltage outputs of the module for a short to ground. If the circuits test normal, replace the faulty module.
  8. Verify that a test lamp illuminates between all ignition voltage circuits and ground.
  9. If the test lamp does not illuminate, repair the circuit for a short to ground or an open/high resistance. If the circuit fuse is open, also test the positive voltage outputs of the module for a short to ground. If the circuits test normal, replace the faulty module.
  10. Test for less than 1 ohm of resistance between the module ground circuits and ground.
  11. If greater than 1 ohm, repair the ground circuit for an open.
  12. Test for less than 1 ohm of resistance in the GMLAN serial data circuit(s) between the non-communicating module and the module that displays the DTC.
  13. If greater than 1 ohm of resistance, test the GMLAN serial data circuit(s) for open/high resistance.
  14. If all circuits test normal, replace the module that is not communicating.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Control Module References for module replacement, setup, and programming
    •  GMLAN Wiring Repairs