GM Service Manual Online
For 1990-2009 cars only

Tools Required

J 44212 Camshaft Holding Tool

Removal Procedure

  1. Remove the right secondary camshaft drive chain. Refer to Secondary Camshaft Drive Chain Replacement - Right Side .
  2. Remove the left secondary drive chain tensioner. Refer to Secondary Camshaft Drive Chain Tensioner Replacement - Left Side .
  3. Remove the left camshaft cover. Refer to Camshaft Cover Replacement - Left Side .

  4. Object Number: 517149  Size: SH
  5. Ensure both camshaft sprocket drive pins are at the top of their rotation.
  6. Caution: Refer to Camshaft Holding Tool Caution in the Preface section.


    Object Number: 650538  Size: SH
  7. Install the J 44212 over the camshafts.
  8. Notice: Refer to Torque Reaction Against Timing Drive Chain Notice in the Preface section.


    Object Number: 749356  Size: SH
  9. Use an open end wrench on the hex cast into the camshaft in order to prevent the camshaft from rotating when removing the camshaft sprocket bolt.

  10. Object Number: 650547  Size: SH
  11. Remove the left intake camshaft sprocket bolt.
  12. Slide the left intake camshaft sprocket off of the camshaft and remove the left secondary camshaft drive chain from the camshaft sprocket teeth.

  13. Object Number: 685362  Size: SH
  14. Lift the left secondary camshaft drive chain from the camshaft intermediate drive shaft sprocket teeth.
  15. Remove the left secondary camshaft drive chain from the engine.
  16. Clean and inspect the camshaft timing drive components. Refer to Camshaft Timing Drive Components Cleaning and Inspection .

Installation Procedure


    Object Number: 685362  Size: SH
  1. Install the left secondary camshaft drive chain by sliding the chain down through the left cylinder head and placing the chain on the left exhaust camshaft sprocket.
  2. Route the left secondary camshaft drive chain around the inner row of the camshaft intermediate drive shaft sprocket teeth.

  3. Object Number: 517149  Size: SH
  4. Install the left intake camshaft sprocket into the left secondary camshaft drive chain.
  5. Install the left intake camshaft sprocket onto the camshaft. The camshaft sprocket notch marked LI (left intake) engages the intake camshaft pin.
  6. Notice: Refer to Torque Reaction Against Timing Drive Chain Notice in the Preface section.


    Object Number: 749356  Size: SH
  7. Use an open end wrench on the hex cast into the camshaft in order to prevent the camshaft from rotating when tightening the camshaft sprocket bolt.
  8. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

  9. Install the left intake camshaft sprocket bolt.
  10. Tighten
    Tighten the camshaft sprocket bolt to 120 N·m (89 lb ft).


    Object Number: 650538  Size: SH
  11. Remove the J 44212 from the camshafts.
  12. Install the left camshaft cover. Refer to Camshaft Cover Replacement - Left Side .
  13. Install the left secondary drive chain tensioner. Refer to Secondary Camshaft Drive Chain Tensioner Replacement - Left Side .
  14. Install the right secondary camshaft drive chain. Refer to Secondary Camshaft Drive Chain Replacement - Right Side .