| Table 1: | HO2S Voltages |
Circuit Description
The wide band heated oxygen sensor (HO2S) measures the amount of oxygen in the exhaust system and provides more information than the switching style HO2S. The wide band sensor consists of an oxygen sensing cell, an oxygen pumping cell, and a heater. The exhaust gas sample passes through a diffusion gap between the sensing cell and the pumping cell. The engine control module (ECM) supplies a voltage to the HO2S and uses this voltage as a reference to the amount of oxygen in the exhaust system. An electronic circuit within the ECM controls the pump current through the oxygen pumping cell in order to maintain a constant voltage in the oxygen sensing cell. The ECM monitors the voltage variation in the sensing cell and attempts to keep the voltage constant by increasing or decreasing the amount of current flow, or oxygen ion flow, to the pumping cell. By measuring the amount of current required to maintain the voltage in the sensing cell, the ECM can determine the concentration of oxygen in the exhaust. The HO2S voltage is displayed as a lambda value. A lambda value of 1 is equal to a stoichiometric air fuel ratio of 14.7:1. Under normal operating conditions, the lambda value will remain around 1. When the fuel system is lean, the oxygen level will be high and the lambda signal will be high or more than 1. When the fuel system is rich, the oxygen level will be low, and the lambda signal will be low or less than 1. The ECM uses this information to maintain the correct air/fuel ratio.
DTC Descriptors
This diagnostic procedure supports the following DTCs:
| • | DTC P0133 HO2S Slow Response Bank 1 Sensor 1 |
| • | DTC P0153 HO2S Slow Response Bank 2 Sensor 1 |
Conditions for Running the DTC
| • | Before the ECM can report DTC P0133 or P0153 failed, DTCs P0121, P0122, P0123, P0221, P0222, P0223, P0336, P0338, P2237, and P2240 must run and pass. |
| • | DTCs P0030, P0031, P0032, P0050, P0051, P0052, P0053, P0059, P0130, P0131, P0132, P0135, P0150, P0151, P0151, P0152, P0155, P0442, P0443, P0446, P0455, P0458, P0459, P0496, P167A, P167B, P2096, P2097, P2098, P2099, P2231, P2234, P2243, P2247, P2251, P2254, P2297, P2298, P2626, and P2629 are not set. |
| • | The HO2S is at operating temperature. |
| • | The HO2S is between 0.94-1.06 lambda. |
| • | The engine speed is between 1,480-2,040 RPM. |
| • | The volumetric efficiency is between 16.5-38.3 percent. |
| • | The change in volumetric efficiency is less than 3 percent. |
| • | The evaporative emission (EVAP) purge is not active, or the ECM determines the EVAP hydrocarbon (HC) concentration is less than a predetermined amount when EVAP purge is active. |
| • | The long term fuel trim correction is active. |
| • | DTC P0133 and P0153 run continuously once the above conditions are met for 10 minutes. |
Conditions for Setting the DTC
| • | The ECM has determined that the dynamic value of the affected HO2S is less than a predetermined threshold. |
| • | The above condition is met for more than 4 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 4 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Use the J 35616-A/BT-8637 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector. |
| • | The lower connector of the ECM is connector C1 and the upper connector of the ECM is connector C2. Refer to Engine Controls Component Views . |
| • | The front wide band sensors do not toggle or switch like a switching HO2S. The front HO2S signals will be relatively stable for an idling engine. |
| • | For an intermittent condition, refer to Intermittent Conditions . |
| • | The following table illustrates the typical voltages for the HO2S circuits: |
HO2S Circuit | Voltage | ||||
|---|---|---|---|---|---|
| |||||
Heater Control | 4.6-5.0 V | ||||
Heater Supply Voltage | B+ | ||||
Reference Voltage | 2.6-3.1 V | ||||
Low Reference | 2.2-2.7 V | ||||
Pump Current | Less than 0.5 | ||||
Input Pump Current | Less than 0.5 | ||||
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step determines if the condition exists.
-
This step determines if the fuel system is contaminated.
Step | Action | Yes | No | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views | |||||||||||
1 | Did you perform the Diagnostic System Check - Vehicle? | Go to Step 2 | |||||||||
|
Important:
Did DTC P0133 and/or DTC P0153 fail this ignition? | Go to Step 4 | Go to Step 3 | |||||||||
3 |
Did the DTC fail this ignition? | Go to Step 4 | Go to Diagnostic Aids | ||||||||
Did DTC P0133 and DTC P0153 fail this ignition cycle? | Go to Step 7 | Go to Step 5 | |||||||||
5 | Inspect for an exhaust leak near the HO2S. Refer to Exhaust Leakage . After you inspect the exhaust system, return to this diagnostic. Did you find and correct the condition? | Go to Step 8 | Go to Step 6 | ||||||||
6 | Inspect or test for the following conditions:
Did you find and correct the condition? | Go to Step 8 | Go to Step 7 | ||||||||
7 |
Important: If both DTCs are set, determine and correct the cause of the contamination before replacing a sensor.
Did you complete the replacement? | Go to Step 8 | -- | ||||||||
8 |
Did the DTC fail this ignition? | Go to Step 2 | Go to Step 9 | ||||||||
9 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | System OK | |||||||||
