GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptor

DTC P0461: Fuel Level Sensor 1 Performance

Diagnostic Fault Information

Circuit

Short to Ground

Open/High Resistance

Short to Voltage

Signal Performance

Fuel Level Sensor Reference Voltage Circuit

P0462

--

--

P0461

Fuel Level Sensor Signal Circuit

P0462

P0463

P0464

P0463

P0461

Fuel Level Sensor Low Reference Circuit

--

P0463

P0464

P0463

P0461

Circuit/System Description

The primary fuel level sender and the secondary fuel level sender changes resistance based on fuel level. The engine control module (ECM) monitors the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to determine the fuel level. When the fuel tank is full, the resistances of both fuel level senders are high and the ECM senses a high signal voltage on both the signal circuits of the primary fuel level sender and the secondary fuel level sender. When the fuel tanks are empty, the resistances of the fuel level senders are low and the ECM senses a low signal voltage. The ECM uses the signal circuits of the primary fuel level sender and the secondary fuel level sender in order to calculate the percentage of remaining fuel in the tank. The ECM sends the fuel level percentage via serial data circuit to the instrument cluster in order to control the fuel gage.

Conditions for Running the DTC

    • The engine is running.
    • No fuel level sensor signal failure present.
    • The fuel level state is stable.

Conditions for Setting the DTC

    • The ECM detects a difference between the engine consumed fuel and change of the fuel level signal of less than 1 L (0.26 gallon) over a range of 30 L (7.92 gallons) or 45.6 percent of the primary fuel tank.
    • The above condition is present for about 300 seconds.

Action Taken When the DTC Sets

    • The fuel gage defaults to empty.
    • The low fuel indicator illuminates.
    • The ECM records the operating conditions at the time that the diagnostic test fails. The ECM displays the failure information in the Failure Records on the scan tool.

Conditions for Clearing the DTC

    • The DTC becomes history when the conditions for setting the DTC are no longer present.
    • The history DTC clears after 40 malfunction-free warm-up cycles.
    • The ECM receives a clear code command from the scan tool.

Diagnostic Aids

A partially filled fuel tank and filling the fuel tank with the ignition ON or engine RUNNING may cause an inaccurate or erratic fuel gage. This condition may cause a fuel system DTC to set and the fuel gage to default to empty. Refer to Fuel Gage Description and Operation

Reference Information

Schematic Reference

    •  Instrument Cluster Schematics
    •  Engine Control Module Connector End Views for the 6.0L engine
    •  Engine Controls Schematics for the 3.6L engine
    •  Engine Controls Schematics for the 2.8L engine

Connector End View Reference

    •  Displays and Gages Connector End Views
    •  Engine Controls Schematics for the 6.0L engine
    •  Engine Control Module Connector End Views for the 3.6L engine
    •  Engine Control Module Connector End Views for the 2.8L engine

Description and Operation

Fuel Gage Description and Operation

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

Scan Tool Reference

Scan Tool Data List

Circuit/System Testing

  1. Ignition OFF, remove the fuel level sender and verify that there are no obstructions interfering with the fuel level sender.
  2. If any interference is present, remove the obstruction.
  3. If no interference is present, perform the fuel level sensor component test before replacing the primary fuel level sensor.

Component Testing

  1. Ignition OFF, disconnect the harness connector at the primary fuel level sensor.
  2. While sweeping the primary fuel level sensor through its full range of motion, test for a minimum value less than 41 ohms and a maximum value greater than 119 ohms of resistance between signal terminal A and the low reference terminal D.
  3. If not within the specified range, replace the primary fuel level sensor.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Primary Fuel Level Sensor Replacement for the 6.0L engine
    •  Primary Fuel Level Sensor Replacement for the 3.6L engine
    •  Primary Fuel Level Sensor Replacement for the 2.8L engine
    •  Control Module References for the ECM replacement, setup, and programming