Battery Positive Cable Replacement LP1, LY7

Important: 

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .
2. Remove the transmission. Refer to Transmission Replacement or Transmission Replacement .
3. Disconnect the battery positive cable from the battery.



4. Depress the tabs in order to remove the cover from the electrical center.



5. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.



6. Reposition the protective boot from the generator output BAT terminal for access.
7. Remove the generator output BAT terminal nut (3) and disconnect the battery positive lead (2) from the generator.



8. Remove the starter terminal nut (1) and disconnect the battery positive cable (2) from the starter.
9. Lower the vehicle.
10. Remove the battery positive cable from the engine.

1. Position the battery positive cable to the engine.
2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle .

Notice: Refer to Fastener Notice in the Preface section.




3. Connect the battery positive cable (2) to the starter and install the starter terminal nut (1).

Tighten
Tighten the nut to 13 N·m (115 lb in).




4. Connect the battery positive lead (2) to the generator and install the generator BAT terminal nut (3).

Tighten
Tighten the nut to 13 N·m (115 lb in).

5. Install the protective boot to the generator output BAT terminal.
6. Lower the vehicle.



7. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block.

Tighten
Tighten the nut to 15 N·m (11 lb ft).




8. Install the electrical center cover.



9. Connect the battery positive cable to the battery.

Tighten
Tighten the battery cable to 17 N·m (13 lb ft).

10. Install the transmission. Refer to Transmission Replacement for the Aisin A/6 transmission or Transmission Replacement for the 5L40-E/5L50-E transmission.
11. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .

Battery Positive Cable Replacement LS6

Important: 

1. Disconnect the battery negative cable (2). Refer to Battery Negative Cable Disconnection and Connection .
2. Disconnect the battery positive cable from the battery.



3. Remove the wiring harness from the retaining features on the underhood fuse block cover.
4. Depress the tabs in order to remove the underhood fuse block cover from the underhood fuse block.



5. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.
6. Disconnect the cable retaining clip from the stud.
7. Remove the transmission. Refer to Transmission Replacement in Manual Transmission - Tremec 6 - Speed.



8. Remove the positive battery cable from the starter motor.
9. Remove the positive battery cable from the retaining features on the clutch housing mounting bolts.
10. Remove the left front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement in Body Front End.



11. Remove the positive battery cable from the retaining features on the engine block.
12. Pull back the rubber boot and remove the generator output BAT terminal nut.
13. Remove the positive battery cable from the vehicle.

1. Position the battery positive cable to the vehicle.

Notice: Refer to Fastener Notice in the Preface section.

2. Install the battery positive cable and nut to the generator.

Tighten
Tighten the battery positive cable to generator output BAT terminal nut to 13 N·m (115 lb in).




3. Install the positive battery cable to the retaining features on the engine block.
4. Install the left front wheelhouse liner. Refer to Front Wheelhouse Liner Replacement in Body Front End.
5. Install the positive battery cable to the retaining features on the clutch housing mounting bolts.
6. Install the positive battery cable to the starter motor.

Tighten
Tighten the battery positive cable to starter motor nut to 10 N·m (89 lb in).




7. Install the transmission. Refer to Transmission Replacement in Manual Transmission - Tremec 6 - Speed.
8. Connect the cable retaining clip to the stud.
9. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block.

Tighten
Tighten the battery positive cable to underhood fuse block nut to 15 N·m (11 lb ft).




10. Install the underhood fuse block cover to the underhood fuse block.
11. Install the wiring harness to the retaining features on the underhood fuse block cover.



12. Connect the battery positive cable to the battery.

Tighten
Tighten the battery cable to 17 N·m (13 lb ft).

13. Connect the battery negative cable (2). Refer to Battery Negative Cable Disconnection and Connection .

Battery Positive Cable Replacement RHD

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .



2. Disconnect the battery positive cable from the battery.



3. Remove the surge tank inlet hose from the retaining feature of the underhood fuse block cover.



4. Depress the tabs in order to remove the underhood fuse block cover from the underhood fuse block.



5. Remove the nut (1) securing the battery positive cable (2) to the underhood fuse block.
6. Remove the starter heat shield. Refer to Starter Shield Replacement .



7. Reposition the protective boot from the generator output BAT terminal for access.
8. Remove the generator output BAT terminal nut (1) and disconnect the battery positive lead (2) from the generator.



9. Remove the starter terminal nut (2) and disconnect the battery positive cable (1) from the starter.
10. Lower the vehicle.



11. Disconnect the cable harness clip (2) from the lift bracket.



12. Disconnect the cable harness clips (2) from the rear bracket and vent housing.
13. Remove the battery positive cable (1) from the engine.

1. Position the battery positive cable (1) to the engine.

Connect the cable harness clips (2) to the rear bracket and vent housing.




2. Connect the cable harness clip (2) to the lift bracket.
3. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.

Notice: Refer to Fastener Notice in the Preface section.




4. Connect the battery positive cable (1) to the starter and install the starter terminal nut (2).

Tighten
Tighten the nut to 13 N·m (115 lb in).




5. Connect the battery positive lead (2) to the generator and install the generator output BAT terminal nut (1).

Tighten
Tighten the nut to 13 N·m (115 lb in).

6. Press the protective boot on to the generator output BAT terminal.
7. Install the starter heat shield. Refer to Starter Shield Replacement .
8. Lower the vehicle.



9. Install the nut (1) securing the battery positive cable (2) to the underhood fuse block.

Tighten
Tighten the nut to 15 N·m (11 lb ft).




10. Install the underhood fuse block cover to the underhood fuse block.



11. Position the surge tank inlet hose to the retaining feature of the underhood fuse block cover.



12. Connect the battery positive cable to the battery.

Tighten
Tighten the battery cable to 17 N·m (13 lb ft).

13. Connect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection .