GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The passenger roof rail deployment loop consists the following components:

    • An inflatable restraint side impact module - Right
    • The roof rail impact module - Right high circuit
    • The roof rail impact module - Right low circuit

A shorting bar used within the roof rail module connector will short together both roof rail module - right high and low circuits, when the connector is disconnected. This will help to prevent unwanted deployment of the inflator module during servicing. During a side or frontal crash of sufficient force, the inflatable restraint sensing and diagnostic module (SDM) will allow current to flow through the deployment loop, in order to deploy the roof side rail module. The SDM performs continuous diagnostic tests on the deployment loops to check for proper circuit continuity, and for shorts to ground or voltage. If a malfunction is detected, a DTC will be stored in memory.

DTC Descriptors

This diagnostic procedure supports the following DTCs:

    • DTC B0069 Right Front Roof Rail Deployment Loop Resistance Low
    • DTC B0070 Right Front Roof Rail Deployment Loop Open
    • DTC B0071 Right Front Roof Rail Deployment Loop Voltage Out of Range

Conditions for Running the DTC

Ignition 1 voltage is within the normal operating voltage range.

Conditions for Setting the DTC

    • DTC B0069 will set when the roof rail module - right deployment loop resistance is less than 1.3 ohms for 500 milliseconds.
    • DTC B0070 will set when one of the following conditions occurs:
       - Roof rail module - right high circuit is less than 2.4 volts, and the roof rail module - right deployment loop is more than 6 ohms for 500 milliseconds.
       - Roof rail module - right deployment loop resistance is more than 4.8 ohms for 500 milliseconds.
    • DTC B0071 when one of the following conditions occur:
       - Roof rail module - right high and/or low circuits are short to ground, or short to voltage for 500 milliseconds.
       - Roof rail module - right high circuit is less than 2.4 volts, and roof rail module - right deployment loop resistance is less than 6 ohms for 500 milliseconds.

Action Taken When the DTC Sets

The SDM commands the AIR BAG indicator ON via class 2 serial data.

Conditions for Clearing the DTC

    • The condition responsible for setting the DTC no longer exists and the scan tool Clear DTCs function is used.
    • A history DTC will clear once 255 malfunction-free ignition cycles have occurred.

Diagnostic Aids

The following are possible causes of the malfunction:

    • A short between the roof rail module - right high and low circuits
    • An open or a high resistance in the roof rail module - right high or low circuits
    • A short to ground or a short to voltage in the roof rail module - right high or low circuits
    • The roof rail module - right connector
    • The SDM connector
    • A malfunctioning roof rail module - right
    • A malfunctioning SDM

Thoroughly inspect the wiring and the connectors. An incomplete inspection of the wiring and the connectors may result in a misdiagnosis, causing a part replacement with the reappearance of the malfunction. If an intermittent malfunction exists, refer to Testing for Intermittent Conditions and Poor Connections .

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests to see if the malfunction is caused by the roof rail module - right.

  2. This step tests to see what DTCs are present. If DTC B0069 is present, test the roof rail module - right for a short between high and low circuits. If DTC B0070 is present, test the roof rail module - right high and low circuits for an open and for high resistance. If DTC B0071 is present, test the roof rail module - right high and low circuits for a short to ground and for a short to voltage.

Step

Action

Yes

No

Schematic Reference: SIR Schematics

Connector End View Reference: SIR Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

  1. Turn OFF the ignition.
  2. Disconnect roof rail module - right in-line connector. Refer to Inflatable Restraint Roof Side Rail Module Replacement - Right Side .
  3. Inspect the component and harness sides of the in-line connector for the roof rail module - right, for damage or corrosion that may cause the malfunction. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Does connector exhibits any signs of damage or corrosion?

Go to Step 3

Go to Step 4

3

  1. If the in-line connector for the roof rail module - right is damaged, the roof rail module - right must be replaced. Refer to Inflatable Restraint Roof Side Rail Module Replacement - Right Side .
  2. If the wiring harness side of the roof rail module - right connector is damaged, replace the harness side of the connector. Refer to Connector Repairs .

Did you complete the repair?

Go to Step 9

--

4

    Important: If scan tool displays multiple codes, diagnose the open code first.

  1. Connect the J 38715-A Driver/Passenger SIR Load Tool to the harness side of the roof rail module - right connector. Use passenger inflator connector.
  2. Turn ON the ignition, with the engine OFF.
  3. With the scan tool, request the SIR DTC display.

Does the scan tool indicate that DTC B0069, B0070, or B0071 are current?

Go to Step 5

Go to Step 7

5

  1. Turn OFF the ignition.
  2. Disconnect and remove the J 38715-A .
  3. Disconnect the inflatable restraint sensing and diagnostic module (SDM) connector. Refer to Control Module References for replacement, setup, and programming.
  4. Inspect the SDM connector for damage or corrosion that may cause a malfunction in the roof rail module - right high and/or low circuits. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 6

6

  1. If DTC B0069 is present, test the roof rail module - right circuits for a short between the high and low circuits.
  2. If DTC B0070 is present, test the roof rail module - right high and low circuits for an open and for high resistance.
  3. If DTC B0071 is present, test the roof rail module - right high and low circuits for a short to ground and for a short to voltage.
  4. All the conditions refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 9

Go to Step 8

7

  1. Turn OFF the ignition.
  2. Replace the roof rail module - right. Refer to Inflatable Restraint Roof Side Rail Module Replacement - Right Side .

Did you complete the replacement?

Go to Step 9

--

8

  1. Turn OFF the ignition.
  2. Replace the SDM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 9

--

9

  1. Connect all SIR components.
  2. Turn ON the ignition, with the engine OFF.
  3. Use the scan tool in order to clear the DTCs.
  4. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.

Does the DTC reset?

Go to Step 2

System OK