GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The engine control module (ECM) checks the system voltage to make sure that the voltage stays within the proper range. Damage to components, and incorrect input can occur when the voltage is out of range. The ECM monitors the system voltage over an extended length of time. If the ECM detects an excessively low system voltage, DTC P0562 will set.

Conditions for Running the DTC

    • Engine speed above 1,500 RPM.
    • System voltage between 9.5-18 volts.

Conditions for Setting the DTC

The ECM detects a system voltage below 10 volts for 5 seconds.

Action Taken When the DTC Sets

    • The ECM will command a message to be displayed.
    • The ECM will not illuminate the malfunction indicator lamp (MIL).
    • The ECM will store conditions which were present when the DTC set as Fail Records data only.

Conditions for Clearing the DTC

    • The ECM will command the message OFF after one trip in which the diagnostic test has been run and passed.
    • The history DTC will clear after 40 consecutive warm-up cycles have occurred without a malfunction.
    • The DTC can be cleared by using the scan tool Clear DTC Information function.

Step

Action

Value(s)

Yes

No

Schematic Reference: Engine Controls Schematics in Engine Controls - 2.6L and 3.2L, Engine Controls Schematics in Engine Controls - 3.6L (LY7), or Engine Controls Schematics in Engine Controls - 5.7L

Connector End View Reference: Engine Control Module Connector End Views in Engine Controls - 2.6L and 3.2L, Engine Control Module Connector End Views in Engine Controls - 3.6L (LY7), or Powertrain Control Module Connector End Views in Engine Controls - 5.7L

1

Did you perform the Vehicle Diagnostic System Check?

--

Go to Step 2

Go to Diagnostic System Check - Engine Electrical

2

  1. Install a scan tool.
  2. Start the engine.
  3. Raise the engine speed above 1,500 RPM.
  4. With a scan tool, observe the Ignition 1 Signal parameter in the ECM data list .

Does the scan tool indicate that the Ignition 1 Signal parameter is greater than the specified range?

10.5 V

Go to Step 6

Go to Step 3

3

Using a scan tool compare the Battery Voltage Signal parameter in the BCM data list with the Ignition 1 Signal parameter in the ECM data list.

Is the Battery Voltage and Ignition 1 Signal parameter readings different by more than the value specified?

0.5 V

Go to Step 4

Go to Charging System Test

4

Test the battery positive voltage circuit of the ECM for a high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 7

Go to Step 5

5

Inspect for poor connections at the harness connector of the ECM. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

--

Go to Step 7

Go to Step 6

6

Important: The replacement PCM must be programmed.

Replace the PCM. Refer to Engine Control Module Replacement in Engine Controls - 2.6L and 3.2L, Engine Control Module Replacement in Engine Controls -3.6L (LY7), or Powertrain Control Module Replacement in Engine Controls - 5.7L.

Did you complete the replacement?

--

Go to Step 7

--

7

  1. Review and record the scan tool Fail Records data.
  2. Use the scan tool in order to clear the DTC.
  3. Operate the vehicle within the Conditions for Running the DTC as specified in the supporting text.
  4. Using the scan tool, observe the Specific DTC Information for DTC P0562 until the test runs.

Does the scan tool indicate that DTC P0562 failed this ignition?

--

Go to Step 2

System OK