Circuit Description
The commanded throttle position is compared to the actual throttle position based on the accelerator pedal position, and possibly other limiting factors. Both values should be within a calibrated range of each other. The powertrain control module (PCM) continuously monitors the commanded and the actual throttle positions. This DTC sets if the values are greater than the calibrated range.
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P2101 Control Module Throttle Actuator Position Performance
Conditions for Running the DTC
| • | The ignition is in the Crank or Run position. |
| • | The system is not in Battery Saver mode. |
| • | The ignition voltage is more than 5.23 volts. |
| • | The communication between the TAC module and the PCM must be valid. |
Conditions for Setting the DTC
| • | The TAC module detects that the commanded and the actual throttle positions are not within a calibrated range of each other. |
| OR |
| • | The TAC module or the PCM cannot determine throttle position. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) when the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The control module stores this information in the Freeze Frame and/or the Failure Records. |
| • | The control module commands the TAC system to operate in the Reduced Engine Power mode. |
| • | A message center or an indicator displays Reduced Engine Power. |
| • | Under certain conditions the control module commands the engine OFF. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Clear the MIL and the DTC with a scan tool. |
Diagnostic Aids
| • | Inspect for mechanical conditions or for binding that may be temperature related. Components may not move freely in extreme heat or cold due to the presence of contaminants or ice formation. |
| • | If the condition is intermittent, refer to Intermittent Conditions . |
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views and Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
2 | Is DTC P2108 also set? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | Go to Step 3 |
3 | Is DTC U0107 also set? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | Go to Step 4 |
4 |
Does the throttle position (TP) sensor 1 and TP sensor 2 angle increase to near the specified value as the pedal is depressed and decrease as the pedal is released? | 100% | Go to Diagnostic Aids | Go to Step 5 |
5 | Test the electronic throttle control (ETC) ignition 1 voltage circuit for high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 7 | Go to Step 6 |
6 | Replace the throttle body assembly. Refer to Throttle Body Assembly Replacement . Did you complete the replacement? | -- | Go to Step 7 | -- |
7 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 8 |
8 |
Important: Be aware that repairing one individual condition may correct more than one DTC. Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
