Caution: Remove the fuel tank cap and relieve the fuel system pressure before servicing the fuel system in order to reduce the risk of personal injury. After you relieve the fuel system pressure, a small amount of fuel may be released when servicing the fuel lines, the fuel injection pump, or the connections. In order to reduce the risk of personal injury, cover the fuel system components with a shop towel before disconnection. This will catch any fuel that may leak out. Place the towel in an approved container when the disconnection is complete.

Notice: Servicing of the supercharger unit itself is limited to replacement only. No attempt should be made to disassemble the supercharger, as parts damage may result.

1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
2. Remove the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .



3. Remove the exhaust gas recirculation (EGR) valve heat shield nut, bolt and the heat shield.
4. Remove the supercharger drive belt. Refer to Drive Belt Replacement .
5. Remove the right spark plug wires from the ignition control module and reposition. Refer to Spark Plug Wire Replacement in Engine Controls - 3.8L.
6. Remove the generator brace. Refer to Generator Brace Replacement in Engine Electrical.
7. Remove the MAP sensor bracket. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.8L.



8. Relieve the fuel pressure. Refer to Fuel Pressure Relief in Engine Controls - 3.8L.
9. Remove the fuel rail assembly. Refer to Fuel Injection Fuel Rail Assembly Replacement in Engine Controls - 3.8L.
10. Remove the boost control solenoid. Refer to Boost Control Solenoid Replacement in Engine Controls - 3.8L.
11. Disconnect the vacuum lines from the following:

•	Fuel pressure regulator valve

•	Supercharger

•	Supercharger bypass valve

•	Manifold vacuum source

12. Disconnect the electrical connectors from the following:

•	Supercharger bypass valve

•	Exhaust gas recirculation (EGR) valve

•	EVAP purge valve

•	Mass air flow (MAF) sensor

•	Throttle position (T/P) sensor

•	Idle air control (IAC) valve

•	Intake air temperature sensor (IAT)

13. Remove the accelerator and the cruise control cables with the bracket from the throttle body. Refer to Accelerator Control Cable Bracket Replacement in Engine Controls - 3.8L.
14. Remove the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement in Engine Controls - 3.8L.



15. Remove the left side supercharger bolts.



16. Remove the right side supercharger bolts.
17. Remove the supercharger.



18. Remove the supercharger gasket.



19. Remove the supercharger O-ring seals.
20. Clean the lower intake manifold-to-supercharger mating surfaces.
21. If replacing the supercharger remove the following:

•	Throttle body

•

PCV valve

•	Supercharger bypass valve

•	Manifold vacuum source

1. If replacing the supercharger install the following:

•	Manifold vacuum source

•	Supercharger bypass valve

•

PCV valve

•	Throttle body




2. Install the new supercharger O-ring seals.




Important: Do not use any sealer on the gasket.

3. Install the new supercharger gasket.
4. Install the supercharger.

Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.




5. Install the right side supercharger bolts.



6. Install the left side supercharger bolts.

Tighten
Tighten the supercharger bolts starting from the center and working to the outside of the supercharger to 23 N·m (17 lb ft).

7. Install the air cleaner intake duct. Refer to Air Cleaner Inlet Duct Replacement in Engine Controls - 3.8L.
8. Install the accelerator and the cruise control cables with the bracket to the throttle body. Refer to Accelerator Control Cable Bracket Replacement in Engine Controls - 3.8L.
9. Connect the electrical connectors to following:

•	Intake air temperature (IAT) sensor

•	Idle air control (IAC) valve

•	Throttle position (T/P) sensor

•	Mass air flow (MAF) sensor

•	EVAP purge valve

•	Exhaust gas recirculation (EGR) valve

•	Supercharger bypass valve

10. Connect the vacuum lines to the following:

•	Manifold vacuum source

•	Supercharger bypass valve

•	Supercharger

•	Fuel pressure regulator valve

11. Install the boost control solenoid. Refer to Boost Control Solenoid Replacement in Engine Controls - 3.8L.



12. Install the fuel rail assembly. Refer to Fuel Injection Fuel Rail Assembly Replacement in Engine Controls - 3.8L.
13. Install the MAP sensor bracket. Refer to Manifold Absolute Pressure Sensor Replacement in Engine Controls - 3.8L.
14. Install the generator brace. Refer to Generator Brace Replacement in Engine Electrical.
15. Install the right spark plug wires to the ignition control module. Refer to Spark Plug Wire Replacement in Engine Controls - 3.8L.
16. Install the supercharger drive belt. Refer to Drive Belt Replacement .



17. Install the EGR valve heat shield, nut and the bolt.

Tighten
Tighten the nut and the bolt to 10 N·m (89 lb in).

18. Install the fuel injector sight shield. Refer to Fuel Injector Sight Shield Replacement .
19. Connect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection in Engine Electrical.
20. Inspect for fluid or vacuum leaks.