GM Service Manual Online
For 1990-2009 cars only

Important: When replacing a theft deterrent control module with a GM Service Parts Operation (SPO) replacement part, the procedure to set up a new theft deterrent control module must be performed prior to the 10 Minute Re-Learn Procedure.

Tools Required

Tech 2 diagnostic scan tool

Procedure to Set Up a New Theft Deterrent Control Module

Use this procedure only if replacing the theft deterrent control module with a GM SPO replacement part.

  1. Connect the Tech 2 diagnostic scan tool to the vehicle.
  2. Turn ON the ignition , with the engine OFF.
  3. With the scan tool, select Setup New TDM in the Theft Deterrent Module, Special Functions data list.
  4. Follow the scan tool on screen instructions.

Important: 

   • When replacing a theft deterrent control module with a GM SPO replacement part, the module will learn keys immediately. The existing PCM however, must learn the new fuel continue password when the theft deterrent control module is replaced.
   • When replacing a powertrain control module (PCM) with a GM SPO replacement part, after programming, these modules will learn the incoming fuel continue password immediately upon receipt of a password message. Once a password message is received, and a password is learned, a relearn procedure must be performed to change this password again. A PCM which has been previously installed in another vehicle will have learned the fuel continue password of the other vehicle theft deterrent control module and will require performing the 10 Minute Re-Learn Procedure to learn the fuel continue password of the current vehicle theft deterrent control module .
   • When performing the 10 Minute Re-Learn Procedure, all previously learned keys will be erased from the theft deterrent control module memory.
   • Additional keys may be learned immediately after the 10 Minute Re-Learn Procedure. Refer to Adding Keys .
   • When performing the 10 Minute Re-Learn Procedure, 2 master passkey III+ (PK3+) keys are required. If a gray valet key is learned first, the theft deterrent control module will not allow additional keys to be learned.

Tools Required

    • Tech 2 diagnostic scan tool
    • Techline Terminal with current Service Programing System (SPS) software

10 Minute Re-Learn Procedure

Use this procedure after replacing any of the following components:

    • The passkey III+ (PK3+) keys
    • The theft deterrent control module
    • The PCM, see Important above

Important: If replacing a theft deterrent control module with a GM SPO replacement part, ensure the procedure to set up a new theft deterrent control module has been performed prior to the 10 Minute Re-Learn Procedure.

  1. Connect the Tech 2 diagnostic scan tool to the vehicle.
  2. With the scan tool, select Request Info. under Service Programing System and follow the scan tool on screen instructions.
  3. Disconnect the scan tool from the vehicle and connect it to a Techline Terminal with current Service Programing System (SPS) software.
  4. On the Techline Terminal, select Service Programming Systems and follow the Techline Terminal on screen instructions.
  5. Disconnect the scan tool from the Techline Terminal and re-connect it to the vehicle.
  6. With a master passkey III+ (PK3+) key, turn ON the ignition, with the engine OFF.
  7. With the scan tool, select Program ECU under Service Programing System.
  8. At this point, the scan tool must remain connected for the duration of the 10 Minute Re-Learn Procedure.
  9. Observe the SECURITY telltale or the scan tool on screen timer. After approximately 10 minutes the scan tool timer will expire and/or the telltale will turn OFF. The vehicle is now ready to relearn the key information and/or passwords on the next ignition switch transition from OFF to CRANK.
  10. Turn OFF the ignition and wait 5 seconds.
  11. With a master passkey III+ (PK3+) key, start the vehicle. The theft deterrent control module has now learned the key transponder information and the PCM has now learned the fuel continue password.
  12. Turn OFF the ignition and wait 15 seconds minimum.
  13. With a second master passkey III+ (PK3+) key, start the vehicle. The theft deterrent control module has now learned the second master passkey III+ (PK3+) key transponder information.
  14. Learning additional keys, if required. Refer to Adding Keys .
  15. With the scan tool, clear any DTCs.