Circuit Description
The fuel tank pressure (FTP) sensor measures the difference between the air pressure or vacuum in the evaporative emission (EVAP) system, and the outside air pressure. The control module supplies a 5-volt reference and a low reference circuit to the FTP sensor. The FTP sensor signal circuit voltage varies depending on EVAP system pressure or vacuum. If the FTP sensor signal voltage increases above a calibrated value, this DTC sets.
The following table illustrates the relationship between FTP sensor signal voltage and the EVAP system pressure/vacuum.
FTP Sensor Signal Voltage | Fuel Tank Pressure |
|---|---|
High, Approximately 1.5 Volts or More | Negative Pressure/Vacuum |
Low, Approximately 1.5 Volts or Less | Positive Pressure |
DTC Descriptor
This diagnostic procedure supports the following DTC:
DTC P0453 Fuel Tank Pressure (FTP) Sensor Circuit High Voltage
Conditions for Running the DTC
DTC P0453 runs continuously when the engine is running.
Conditions for Setting the DTC
| • | The FTP sensor voltage is more than 4.9 volts. |
| • | All conditions are present for more than 25 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records. |
Conditions for Clearing the DTC
| • | A current DTC Last Test Failed clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other non-emission related diagnostic. |
| • | Clear the DTC with a scan tool. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
This step tests the signal circuit of the FTP sensor.
-
This step tests the 5-volt reference circuit of the FTP sensor.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics Connector End View Reference: Powertrain Control Module Connector End Views or Engine Controls Connector End Views | ||||
1 | Did you perform the Diagnostic System Check - Vehicle? | -- | Go to Step 2 | Go to Diagnostic System Check - Vehicle in Vehicle DTC Information |
Is the Fuel Tank Pressure Sensor parameter more than the specified value? | 4.3 V | Go to Step 4 | Go to Step 3 | |
3 |
Did the DTC fail this ignition? | -- | Go to Step 4 | Go to Intermittent Conditions |
Is the Fuel Tank Pressure Sensor parameter more than the specified value? | 0.2 V | Go to Step 5 | Go to Step 7 | |
5 | Test the FTP low reference circuit for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 6 |
Measure the voltage of the FTP 5-volt reference circuit with a DMM. Refer to Circuit Testing in Wiring Systems. Is the Fuel Tank Pressure Sensor parameter within the specified value? | 4.8-5.2 V | Go to Step 9 | Go to Step 10 | |
7 | Test the FTP signal circuit for a short to voltage or for a short to a 5-volt reference circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
8 | Test for an intermittent and for a poor connection at the control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 12 |
9 | Test for an intermittent and for a poor connection at the FTP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 13 | Go to Step 11 |
10 | Repair the short to voltage in the FTP 5-volt reference circuit. Refer to Wiring Repairs in Wiring Systems. Did you complete the repair? | -- | Go to Step 13 | -- |
11 | Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement . Did you complete the replacement? | -- | Go to Step 13 | -- |
12 | Replace the powertrain control module (PCM). Refer to Control Module References in Computer/Integrating Systems for replacement, setup, and programming. Did you complete the replacement? | -- | Go to Step 13 | -- |
13 |
Did the DTC fail this ignition? | -- | Go to Step 2 | Go to Step 14 |
14 | Observe the Capture Info with a scan tool. Are there any DTCs that have not been diagnosed? | -- | Go to Diagnostic Trouble Code (DTC) List - Vehicle in Vehicle DTC Information | System OK |
