GM Service Manual Online
For 1990-2009 cars only

ABS Description and Operation W/O NW7

This vehicle is equipped with an EBC 325EV ABS/DRP module.

This module provides the following vehicle performance enhancement systems.

    • Antilock Brake System (ABS)
    • Dynamic Rear Proportioning (DRP)

The following components are involved in the operation of the above systems.

    • Electronic brake control module (EBCM) -- The EBCM controls the system functions and detects failures.
        The EBCM contains the following components.
       - System relay -- The system relay is internal to the EBCM. The system relay is energized when the ignition is ON. The system relay supplies battery positive voltage to the valve solenoids and to the ABS pump motor. This voltage is referred to as system voltage.
       - Solenoids -- The solenoids are commanded ON and OFF by the EBCM to operate the appropriate valves in the brake pressure modulator valve (BPMV).
    • Brake pressure modulator valve (BPMV) -- The BPMV uses a 3-circuit configuration to control hydraulic pressure to each front wheel independently, and to the rear wheels as a pair.
        The BPMV contains the following components.
       - ABS pump motor and pump
       - Three isolation valves
       - Three dump valves
       - A front low-pressure accumulator
       - A rear low-pressure accumulator
    • Wheel speed sensors (WSS) -- As the wheels spin, toothed rings interrupt magnetic fields in the wheel speed sensors. This causes each wheel speed sensor to generate an AC signal. The EBCM uses these AC signals to calculate the wheel speed. Any imperfections in the toothed ring, such as a missing or damaged tooth, can cause an inaccurate WSS signal.

Antilock Brake System (ABS) Operation

When wheel slip is detected during a brake application, an ABS event occurs. During antilock braking, hydraulic pressure in the individual wheel circuits is controlled to prevent any wheel from slipping. A separate hydraulic line and specific solenoid valves are provided for each wheel. The ABS can decrease, hold, or increase hydraulic pressure to each wheel. The ABS does not, however, increase hydraulic pressure above the amount which is transmitted by the master cylinder during braking.

During antilock braking, a series of rapid pulsations is felt in the brake pedal. These pulsations are caused by the rapid changes in position of the individual solenoid valves as the electronic brake control module (EBCM) responds to wheel speed sensor inputs and attempts to prevent wheel slip. These pedal pulsations are present only during antilock braking and stop when normal braking is resumed or when the vehicle comes to a stop. A ticking or popping noise may also be heard as the solenoid valves cycle rapidly. During antilock braking on dry pavement, intermittent chirping noises may be heard as the tires approach slipping. These noises and pedal pulsations are considered normal during antilock operation.

Vehicles equipped with ABS may be stopped by applying normal force to the brake pedal. Brake pedal operation during normal braking is no different than that of previous non-ABS systems. Maintaining a constant force on the brake pedal provides the shortest stopping distance while maintaining vehicle stability. The typical ABS activation sequence is as follows.

Pressure Hold

The EBCM closes the isolation valve and keeps the dump valve closed in order to isolate the slipping wheel when wheel slip occurs. This holds the pressure steady on the brake so that the hydraulic pressure does not increase or decrease.

Pressure Decrease

If a pressure hold does not correct the wheel slip condition, a pressure decrease occurs. The EBCM decreases the pressure to individual wheels during deceleration when wheel slip occurs. The isolation valve is closed and the dump valve is opened. The excess fluid is stored in the accumulator until the pump can return the fluid to the master cylinder or fluid reservoir.

Pressure Increase

After the wheel slip is corrected, a pressure increase occurs. The EBCM increases the pressure to individual wheels during deceleration in order to reduce the speed of the wheel. The isolation valve is opened and the dump valve is closed. The increased pressure is delivered from the master cylinder.

Dynamic Rear Proportioning (DRP) Operation

The dynamic rear proportioning (DRP) is a control system that enhances the hydraulic proportioning function of the mechanical proportioning valve in the base brake system. The DRP control system is part of the operation software in the electronic brake control module (EBCM). The DRP uses active control with existing ABS in order to regulate the vehicle's rear brake pressure.

Power-up Self-Test

The electronic brake control module (EBCM) is able to detect many malfunctions whenever the ignition is ON. However, certain failures cannot be detected unless active diagnostic tests are performed on the components. Shorted solenoid coil or motor windings, for example, cannot be detected until the components are commanded ON by the EBCM. Therefore, a power-up self-test is required at the beginning of each ignition cycle to verify correct operation of components before the various control systems can be enabled. The EBCM performs the power-up self-test when the ignition is first turned ON. The system relay, solenoids and the ABS pump motor are commanded ON and OFF to verify proper operation and the EBCM verifies the ability to return the system to base braking in the event of a failure. The power-up self-test may be heard by the driver, depending on how soon the engine is cranked and started after turning ON the ignition.

ECE 13 Response

The electronic brake control module (EBCM) illuminates the ABS indicator when a malfunction which disables ABS is detected. Usually, the ABS indicator is turned OFF during the following ignition cycle unless the fault is detected during that ignition cycle. However, the setting of a wheel speed sensor related DTC may cause the ABS indicator to remain illuminated during the following ignition cycle until the vehicle is operated at a speed greater than 13 km/h (8 mph) or, occasionally, 64 km/h (40 mph), depending on which DTC sets. This allows the EBCM to verify that no malfunction exists, before turning OFF the ABS indicator. It is important to verify that ECE 13 is not the cause of an ABS indicator which is illuminated when no DTCs are set, before attempting to diagnose other possible causes.

Driver Information Indicators and Messages

The following indicators are used to inform the driver of several different factors.

Brake Warning Indicator

The instrument panel cluster (IPC) illuminates the brake warning indicator when the following occurs.

    • The body control module (BCM) detects that the park brake is engaged. The IPC receives a serial data message from the BCM requesting illumination. The brake warning indicator flashes at a rate of approximately twice per second when the park brake is engaged.
    • The electronic brake control module (EBCM) detects a low brake fluid condition or a base brake pressure differential and sends a serial data message to the IPC requesting illumination.
    • The IPC performs the bulb check.
    • The EBCM detects an ABS-disabling malfunction which also disables dynamic rear proportioning (DRP) and sends a serial data message to the IPC requesting illumination.

ABS Indicator

The IPC illuminates the ABS indicator when the following occurs.

    • The electronic brake control module (EBCM) detects an ABS-disabling malfunction and sends a serial data message to the IPC requesting illumination.
    • The IPC performs the bulb check.
    • The IPC detects a loss of serial data communication with the EBCM.
    • A DTC is set during the previous ignition cycle which requires an ECE 13 response at the beginning of the current ignition cycle. The EBCM sends a serial data message to the IPC requesting illumination.

ABS Description and Operation W/NW7

Left Side Frame Rail - w/o JL4


Object Number: 599037  Size: MF
(1)Electronic Brake Control Module (EBCM)
(2)Electronic Brake Control Module (EBCM) Electrical Connector - C1
(3)Electronic Brake Control Module (EBCM) Electrical Connector - C2
(4)Frame

BPMV Hydraulic Flow


Object Number: 394564  Size: LF
(1)Master Cylinder
(2)Master Cylinder Reservoir
(3)Pump
(4)Brake Pressure Modulator Valve (BPMV)
(5)Damper
(6)Rear Isolation Valve
(7)Accumulator
(8)Rear Dump Valve
(9)Right Rear Brake
(10)Left Rear Brake
(11)Left Front Isolation Valve
(12)Left Front Dump Valve
(13)Left Front Brake
(14)Accumulator
(15)Right Front Brake
(16)Right Front Dump Valve
(17)Right Front Isolation Valve
(18)Damper

This vehicle is equipped with one of the following antilock braking systems:

EBC325S (w/NW7)

The vehicle is equipped with the following braking enhancement systems:

    • Antilock Brake System (ABS)
    • Dynamic Rear Proportioning (DRP)
    • Traction Control System (TCS) (w/NW7)

The following components are involved in the operation of the above systems:

    • Electronic brake control module (EBCM) -- The EBCM controls the system functions and detects failures.
        The EBCM contains the following components:
       - System relay -- The system relay is internal to the EBCM. The system relay is energized when the ignition is ON. The system relay supplies battery positive voltage to the solenoid valves and to the pump motor. This voltage is referred to as system voltage.
       - Solenoids -- The solenoids are commanded ON and OFF by the EBCM to operate the appropriate valves in the brake pressure modulator valve (BPMV).
    • Brake pressure modulator valve (BPMV) -- The BPMV uses a 3-circuit configuration to control the left front wheel, the right front wheel, and the combined rear wheels. The BPMV directs fluid to the left front and right front wheels independently. The BPMV directs fluid to the two rear wheels on a single hydraulic circuit.
        The BPMV contains the following components:
       - Pump motor
       - Three isolation valves
       - Three dump valves
       - A front low-pressure accumulator
       - A rear low-pressure accumulator
    • Wheel speed sensors (WSS) -- As the front wheels spin, toothed rings located at each wheel hub interrupt magnetic fields in the wheel speed sensors. This causes each wheel speed sensor to generate an AC signal. The EBCM uses these AC signals to calculate the wheel speed. The wheel speed sensors are serviceable only as part of the wheel hub and bearing assemblies. Any imperfections in the toothed ring, such as a missing or damaged tooth, can cause an inaccurate WSS signal.
    • Vehicle speed sensor (VSS) -- The input signal for rear wheel speed originates at the VSS. The powertrain control module (PCM) receives rear wheel speed input from the VSS and supplies this information to the EBCM.
    • Traction control switch (w/NW7) -- The TCS is manually disabled or enabled using the traction control switch. The TCS can be programmed to be automatically enabled or disabled when the ignition is turned ON. The factory default is for the TCS to be automatically enabled. Refer to Programming the Traction Control Automatic Engagement Feature.

Initialization Sequence

The EBCM performs one initialization test each ignition cycle. The initialization of the EBCM occurs when the following conditions are met:

    • The ignition is ON.
    • The bulb check has been completed.
    • Vehicle speed is greater than 6 km/h (4 mph).

The initialization sequence briefly cycles each solenoid and the pump motor to verify proper operation of the components. The EBCM sets one or more DTCs in accordance with any malfunction that is detected.

The EBCM defines a drive cycle as the completion of the initialization sequence.

Antilock Brake System

When wheel slip is detected during a brake application, the ABS enters antilock mode. During antilock braking, hydraulic pressure in the individual wheel circuits is controlled to prevent any wheel from slipping. A separate hydraulic line and specific solenoid valves are provided for each wheel. The ABS can decrease, hold, or increase hydraulic pressure to each wheel brake. The ABS cannot, however, increase hydraulic pressure above the amount which is transmitted by the master cylinder during braking.

During antilock braking, a series of rapid pulsations is felt in the brake pedal. These pulsations are caused by the rapid changes in position of the individual solenoid valves as the EBCM responds to wheel speed sensor inputs and attempts to prevent wheel slip. These pedal pulsations are present only during antilock braking and stop when normal braking is resumed or when the vehicle comes to a stop. A ticking or popping noise may also be heard as the solenoid valves cycle rapidly. During antilock braking on dry pavement, intermittent chirping noises may be heard as the tires approach slipping. These noises and pedal pulsations are considered normal during antilock operation.

Vehicles equipped with ABS may be stopped by applying normal force to the brake pedal. Brake pedal operation during normal braking is no different than that of previous non-ABS systems. Maintaining a constant force on the brake pedal provides the shortest stopping distance while maintaining vehicle stability.

Pressure Hold

The EBCM closes the isolation valve and keeps the dump valve closed in order to isolate the slipping wheel when wheel slip occurs. This holds the pressure steady on the brake so that the hydraulic pressure does not increase or decrease.

Pressure Decrease

If a pressure hold does not correct the wheel slip condition, a pressure decrease occurs. The EBCM decreases the pressure to individual wheels during deceleration when wheel slip occurs. The isolation valve is closed and the dump valve is opened. The excess fluid is stored in the accumulator until the pump can return the fluid to the master cylinder or fluid reservoir.

Pressure Increase

After the wheel slip is corrected, a pressure increase occurs. The EBCM increases the pressure to individual wheels during deceleration in order to reduce the speed of the wheel. The isolation valve is opened and the dump valve is closed. The increased pressure is delivered from the master cylinder.

Dynamic Rear Proportioning (DRP)

The dynamic rear proportioning (DRP) is a control system that replaces the hydraulic proportioning function of the mechanical proportioning valve in the base brake system. The DRP control system is part of the operation software in the EBCM. The DRP uses active control with existing ABS in order to regulate the vehicle's rear brake pressure.

The red brake warning indicator is illuminated when the dynamic rear proportioning function is disabled.

Traction Control System (TCS)

When drive wheel slip is noted while the brake is not applied, the EBCM will enter traction control mode.

The EBCM uses a 5-volt pulse-width modulated (PWM) signal to request the PCM to reduce the amount of torque to the drive wheels. The PCM reduces torque to the drive wheels by retarding spark timing and by commanding the throttle actuator control. The PCM uses a 5-volt PWM signal in order to report to the EBCM the amount of torque delivered to the drive wheels.

Brake Warning Indicator

The instrument panel cluster (IPC) illuminates the brake warning indicator when the following occurs:

    • The body control module (BCM) detects that the park brake is engaged. The IPC receives a class 2 message from the BCM requesting illumination.
    • The EBCM detects a low brake fluid condition and sends a class 2 message to the IPC.
    • The IPC performs the bulb check.
    • An ABS-disabling malfunction also disables dynamic rear proportioning (DRP).

ABS Indicator

The IPC illuminates the ABS indicator when the following occurs:

    • The electronic brake control module (EBCM) detects an ABS-disabling malfunction. The IPC receives a class 2 message from the EBCM requesting illumination.
    • The IPC performs the bulb check.
    • The IPC detects a loss of class 2 communications with the EBCM.

Traction Control Indicators (w/NW7)

TRACTION ACTIVE

The traction active message is displayed on the instrument panel cluster (IPC) during a traction control event.

TRACTION OFF

The EBCM illuminates the traction off indicator if any of the following conditions are present.

    • The EBCM inhibits the traction control system.
    • The driver manually disables the traction control system by pressing the traction control switch.
    • The automatic transmission shift lever is in the low (1) position.

The EBCM inhibits the traction control system when a TCS-disabling malfunction occurs, or when the automatic engagement feature is programmed to disable the TCS when the ignition is turned ON. Refer to Programming the Traction Control Automatic Engagement Feature.

Programming the Traction Control Automatic Engagement Feature

The automatic engagement feature may be programmed so that the traction control system activates or does not activate automatically at the start of each ignition cycle. In order to change the status of the automatic engagement feature, perform the following procedure:

Important: Failure to follow the correct procedure may cause DTC C0283 to set in EBCM memory.

  1. Park the vehicle and apply the parking brake.
  2. Unlock the ignition and shift the transmission into NEUTRAL (N).
  3. Turn the ignition ON, engine OFF.
  4. Press and hold the brake pedal and the accelerator pedal.
  5. Press and hold the traction assist switch for 5 seconds.
  6. Release the brake and accelerator pedals and the traction control switch.
  7. Turn the ignition OFF.