GM Service Manual Online
For 1990-2009 cars only

Rear Washer Hose Replacement XUV

Removal Procedure


    Object Number: 751308  Size: SH
  1. Disconnect the rear washer hose connection (2) near the coolant tank.
  2. Remove the washer hose grommet (1) from the hole in the bulkhead, and feed the washer hose into the vehicle.
  3. Remove the right front sill plate. Refer to Rear Side Door Sill Plate Replacement in Interior Trim. Roll the carpet inward to expose the wiring harness/hose assembly.
  4. Remove the rear seat backs.
  5. Remove the rear compartment anchors.
  6. Roll the carpet forward to expose the wiring harness/hose assembly.
  7. Remove the left rear quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.

  8. Object Number: 749976  Size: SH
  9. Open the lift gate to access the pass-through grommet.
  10. Disconnect the grommet from the end gate to access the washer hose connection.
  11. Cut the exposed ends of the washer hose from the body wiring harness.
  12. Remove the hose from the vehicle.

Installation Procedure

  1. Install the washer hose to the vehicle.
  2. Route the hose along the body wiring harness.
  3. Tape the washer hose to the body wiring harness with 3 wraps of electrical tape, every 100 mm (4 in).
  4. Roll the carpet back into place along the floor panel.
  5. Install the rear compartment anchors.
  6. Install the rear seat backs.
  7. Install the right front sill plate. Refer to Rear Side Door Sill Plate Replacement in Interior Trim.
  8. Connect the washer hose connection at the end gate.
  9. Connect the pass-through grommet at the end gate.
  10. Install the left rear quarter upper trim panel. Refer to Rear Quarter Upper Trim Panel Replacement in Interior Trim.

  11. Object Number: 751308  Size: SH
  12. Install the rear washer hose out through the bulkhead, and seat the grommet (1).
  13. Connect the rear washer hose connection (2) near the coolant tank.

Rear Washer Hose Replacement TrailBlazer, Envoy

Removal Procedure


    Object Number: 751308  Size: SH
  1. Disconnect the rear washer hose connection (2) near the coolant tank.
  2. Remove the washer hose grommet (1) from the hole in the bulkhead, and feed the washer hose into the vehicle.
  3. Remove the right front sill plate. Refer to Rear Side Door Sill Plate Replacement .
  4. Roll the carpet inward to expose the wiring harness/hose assembly.
  5. Remove the rear seat backs.
  6. Remove the rear compartment anchors.
  7. Roll the carpet forward to expose the wiring harness/hose assembly.
  8. Remove the left rear quarter upper trim panel. Refer to Quarter Upper Trim Panel Replacement .

  9. Object Number: 749976  Size: SH
  10. Open the liftgate to access the pass-through grommet.
  11. Disconnect the grommet from the liftgate to access the washer hose connection.
  12. Cut the exposed ends of the washer hose from the body wiring harness.
  13. Remove the hose from the vehicle.

Installation Procedure

  1. Install the washer hose to the vehicle.
  2. Route the hose along the body wiring harness.
  3. Tape the washer hose to the body wiring harness with 3 wraps of electrical tape, every 100 mm (4 in).
  4. Roll the carpet back into place along the floor panel.
  5. Install the rear compartment anchors.
  6. Install the rear seat backs.
  7. Install the right front sill plate. Refer to Rear Side Door Sill Plate Replacement .

  8. Object Number: 749976  Size: SH
  9. Connect the washer hose connection at the liftgate.
  10. Connect the pass-through grommet the liftgate.
  11. Install the left rear quarter upper trim panel. Refer to Quarter Upper Trim Panel Replacement .

  12. Object Number: 751308  Size: SH
  13. Install the rear washer hose out through the bulkhead, and seat the grommet (1).
  14. Connect the rear washer hose connection (2) near the coolant tank.