The brake pressure modulator valve (BPMV) is mounted on the left front side of the engine compartment. The BPMV provides brake fluid modulation for each of the individual wheel circuits as required during DRP/ABS/TCS/VSES (if equipped). During DRP/ABS, the BPMV can maintain or reduce brake fluid pressure independent of the pressure generated in the master cylinder. The BPMV does not provide more pressure than is applied by the master cylinder during DRP/ABS.
With the exception of the EBCM, the BPMV is an integral, non-serviceable component. The BPMV should never be disassembled.
The BPMV uses a 4 circuit configuration with a diagonal split. Individual circuits are provided for the left front and right rear wheels, and right front and left rear wheels. The diagonal circuits are hydraulically isolated so that a leak or malfunction in one circuit will allow continued braking ability on the other.
The BPMV consists of several other components:
The BPMV contains a motor driven recirculation pump. The pump serves 2 purposes:
The pump and motor are located within the BPMV and are not serviced separately.
The ABS valves decrease or maintain brake fluid pressure at the individual wheel circuits. There are 4 inlet and 4 outlet solenoid valves. The solenoid valves maintain, increase, or decrease brake fluid pressure to the individual wheel circuits. The EBCM commands the valves to their correct position during DRP/ABS/TCS/VSES. During DRP/ABS, the pressure in each hydraulic circuit can be held or released by activating the appropriate valves. The normal state of the inlet valves is open, while the normal state of the outlet valves is closed. This allows direct master cylinder pressure to the brakes during normal braking. The ABS valves are located within the BPMV and are not serviced separately.
The 2 BPMV bracket bolts are used to attach the BPMV to the BPMV bracket. Beneath each BPMV bracket bolt is a rubber isolator. There is also a rubber isolator on the bottom of the BPMV. The isolators reduce the vibration, which is associated with vehicle operation, on the BPMV and EBCM.
The BPMV bracket bolts and isolators are included with a new BPMV or EBCM/BPMV assembly, but may be serviced separately.
With TCS (NW9), there are 2 TCS master cylinder isolation valves within the BPMV. These valves isolate the master cylinder so the pump motor can build brake fluid pressure for the front brakes during TCS/VSES. Unlike the ABS valve solenoids, the isolation valves do not modulate. The isolation valves are normally open and then close during TCS/VSES.
With TCS (NW9), there are 2 TCS prime valves within the BPMV. These valves allow the pump to draw fluid from the master cylinder reservoir, through the compensating ports in the master cylinder bore. The prime valves do not modulate. The prime valves are closed during normal operation and open during TCS/VSES.
The EBCM performs the following functions:
The EBCM continuously checks the speed of each wheel in order to determine if any wheel is beginning to slip. If a wheel slip tendency is detected, the EBCM commands appropriate valve positions in order to modulate brake fluid pressure in some or all of the hydraulic circuits. This prevents wheel slip and provides optimum braking. The EBCM continues to control pressure in individual hydraulic circuits until a slipping tendency is no longer present. If the EBCM detects an error, the EBCM can perform the following actions:
The EBCM transmits torque request signals to and receives delivered torque signals from the PCM.
The system relay provides power to the pump motor during DRP/ABS/TCS/VSES and power to the solenoid valves in the BPMV. This relays is an integral part of the EBCM and cannot be serviced separately.
The electronic brake control module (EBCM) defines a drive cycle as the completion of the EBCM initialization sequence. The EBCM will perform the initialization sequence one time in each ignition cycle. Refer to Initialization Sequence .
With TCS (NW9), the traction control switch, located at the end of the shift lever, is a momentary ON switch that allows the driver to shut off the TCS for personal or diagnostic reasons. Turning the system off places the TCS in passive mode while retaining DRP/ABS/VSES functions. When the TCS system is turned OFF, the TRACTION OFF indicator is turned ON. The switch is located at the end of the shift lever to the right of the steering column.
The stoplamp/auto trans shift lock control switch is an input to the EBCM. The EBCM uses the stoplamp/auto trans shift lock control switch to tell when the brake pedal is being applied so that TCS can be disabled if necessary.
A wheel speed sensor (WSS) is present at each wheel. The sensors transmit wheel speed information to the EBCM by means of a small AC voltage. This voltage is generated by magnetic induction caused by passing the toothed sensor ring (part of the integral hub/bearing assembly) past the stationary sensor. The signal is transmitted to the EBCM through shielded wiring in order to help reduce electromagnetic interference that can cause false or noisy WSS inputs to the EBCM.
The front wheel speed sensors are located in the hub/bearing assembly and are non-adjustable. Sensor gap is set at the time of assembly.
The rear wheel speed sensors are mounted in the bearing assembly and are non-adjustable. Sensor gap is set at the time of assembly.
Pin E of the EBCM harness connector is a plastic vent tube that vents the cavity between the EBCM and the BPMV to the underhood fuse block.
The lateral accelerometer is a self-contained unit which uses a reference voltage of 5 volts. The sensor's operating range is ±1.5 g, resulting in an output range of 0.25-4.75 volts. Zero lateral acceleration results in an output signal of 2.5 volts. The lateral accelerometer is located under the rear driver's side seat cushion, attached to the number 4 bar.
The yaw rate sensor is a self contained unit which uses a reference voltage of 5 volts. The sensor's range is ±75 degrees per second, resulting in a signal proportional output of 0.25-4.75 volts. Zero yaw rate is 2.5 volts. The yaw rate sensor is located behind the rear compartment trim, under the rear package shelf.
The steering wheel position sensor (SWPS) sends dual analog signals to the EBCM. The EBCM determines steering wheel position and rotation from these signals.
