Circuit Description
The control module monitors the fuel tank pressure (FTP) sensor signal in order to detect vacuum decay and excess vacuum during the enhanced evaporative emission (EVAP) diagnostic. The control module supplies a 5-volt reference and ground to the sensor. The FTP sensor signal voltage increases as the FTP decreases, negative pressure or vacuum, high voltage. The FTP sensor signal voltage decreases as the FTP increases, positive pressure, low voltage. When the FTP sensor signal goes below a predetermined value, DTC P0452 will set.
Conditions for Running the DTC
The engine is running.
Conditions for Setting the DTC
| • | The FTP sensor voltage is less than 0.1 volt. |
| • | All conditions present for greater than 5 seconds. |
Action Taken When the DTC Sets
| • | The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails. |
| • | The control module will store conditions which were present when the DTC set as Freeze Frame/Failure Records data. |
Conditions for Clearing the MIL/DTC
| • | The control module turns OFF the malfunction indicator lamp (MIL) after 3 consecutive ignition cycles that the diagnostic runs and does not fail. |
| • | A current DTC, Last Test Failed, clears when the diagnostic runs and passes. |
| • | A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic. |
| • | Use the scan tool in order to clear the MIL and the DTC. |
Test Description
The number below refers to the step number on the diagnostic table.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: Engine Controls Schematics | ||||
1 | Did you perform the Diagnostic System Check-Engine Controls? | -- | Go to Step 2 | |
2 |
Did DTC P1635 or P1639 fail this ignition? | -- | Go to Step 3 | |
3 | With the scan tool, observe the FTP sensor voltage. Does the scan tool indicate that the FTP sensor voltage is less than the specified value? | 0.1 V | Go to Step 5 | Go to Step 4 |
4 |
Does the DTC fail this ignition? | -- | Go to Step 5 | Go to Intermittent Conditions |
Does the scan tool indicate that the FTP voltage is near the specified value? | 5 V | Go to Step 8 | Go to Step 6 | |
6 | Test the 5-volt reference circuit of the FTP sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 7 |
7 | Test the signal circuit of the FTP sensor for a short to ground, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 9 |
8 | Inspect for poor connections at the harness connector of the FTP sensor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 10 |
9 | Inspect for poor connections at the harness connector of the control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 12 | Go to Step 11 |
10 | Replace the FTP sensor. Refer to Fuel Tank Pressure Sensor Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- |
11 | Replace the PCM. Refer to Powertrain Control Module Replacement . Did you complete the replacement? | -- | Go to Step 12 | -- |
12 |
Does the DTC reset? | -- | Go to Step 2 | Go to Step 13 |
13 | Select the Capture Info option and the Review Info option using the scan tool. Does the scan tool display any DTCs that have not been diagnosed? | -- | System OK | |
