Circuit Description
The instrument panel integration module (IPM) commands right air temperature actuator movement with one of three voltage signals applied to the right air temperature door control circuit. A low voltage of 0 volts moves the right air temperature door toward full hot, 2.5 volts stops the actuator, and 5 volts moves the right air temperature door toward full cold. The IPM determines the current position of the actuator by monitoring the feedback voltage of the right air temperature door position signal circuit. The feedback potentiometer position is a function of the actuator position. A high voltage indicates a full cold right air temperature door position. A low voltage indicates a full hot right air temperature door position. The IPM controls the right air temperature door position in order to maintain the selected air temperature on the HVAC control module.
The IPM will perform a continuous test on the current feedback voltage. If the feedback voltage does not equal or fall within the calibrated limits, the DTC will set.
Conditions for Running the DTC
The ignition is turned ON.
Conditions for Setting the DTC
The IPM detects the signal circuit is less than 0.09 volt (5 counts) or greater than 4.90 volts (250 counts).
Action Taken When the DTC Sets
| • | A default value of 2.50 volts (128 counts) will be substituted for the right air temperature door position data by the IPM. |
| • | The IPM will toggle the actuator between full hot and full cool in an attempt to maintain the selected air temperature on the HVAC control module. |
Conditions for Clearing the DTC
| • | The DTC will become history if the IPM no longer detects a failure. |
| • | The history DTC will clear after 50 fault-free ignition cycles. |
| • | The DTC can be cleared with a scan tool. |
Diagnostic Aids
| • | A damaged or broken right air temperature door and or actuator can cause this DTC to set by allowing the actuator shaft to rotate unrestricted to its internal stop (overtravel condition). The internal stops are outside of the feedback potentiometers 0-250 count working range. |
| • | If the condition is not present, refer to Testing for Intermittent Conditions and Poor Connections in Wiring Systems. |
Test Description
The numbers below refer to the step numbers on the diagnostic table.
-
Tests for the proper operation of the circuit in the high voltage range.
-
Tests for the proper operation of the circuit in the low voltage range. If the fuse in the jumper opens when you perform this test, the signal circuit is shorted to voltage.
-
Tests for a short to ground in the 5-volt reference circuit.
Step | Action | Values | Yes | No |
|---|---|---|---|---|
Schematic Reference: HVAC Schematics | ||||
1 | Did you perform the HVAC Diagnostic System Check? | -- | Go to Step 2 | |
2 |
Does the scan tool indicate that the Right Temp Dr Actual parameter is within the specified range? | 0.09-4.90 V | Go to Diagnostic Aids | Go to Step 3 |
3 |
Does the scan tool indicate that the Right Temp Dr Actual parameter changes when the Right Temp Dr is commanded from Hot to Cold? | -- | Go to Step 12 | Go to Step 4 |
Does the scan tool indicate that the Right Temp Dr Actual parameter is greater than the specified value? | 4.90 V | Go to Step 5 | Go to Step 9 | |
Does the scan tool indicate that the Right Temp Dr Actual parameter is less than the specified value? | 0.09 V | Go to Step 6 | Go to Step 10 | |
Does the scan tool indicate that the Right Temp Dr Actual parameter is greater than the specified value? | 4.90 V | Go to Step 8 | Go to Step 7 | |
7 | Test the 5-volt reference circuit of the right air temperature actuator for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
8 | Test the 5-volt reference circuit of the right air temperature actuator for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 13 |
9 | Test the door position signal circuit of the right air temperature actuator for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
10 | Test the door position signal circuit of the right air temperature actuator for a short to voltage, a high resistance, or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 11 |
11 | Test the low reference circuit of the right air temperature actuator for a high resistance or an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 14 |
12 | Inspect the right air temperature door for a condition allowing excessive travel of the actuator. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 13 |
13 | Inspect for poor connections at the harness connector of the right air temperature actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 15 |
14 | Inspect for poor connections at the harness connector of the instrument panel integration module (IPM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems. Did you find and correct the condition? | -- | Go to Step 17 | Go to Step 16 |
15 |
Important: : Perform the Recalibration procedure for the right air temperature actuator. Replace the right air temperature actuator. Refer to Air Temperature Actuator Replacement - Right Side . Did you complete the replacement? | -- | Go to Step 17 | -- |
16 |
Important: : Perform the Recalibration procedure for the instrument panel integration module. Replace the instrument panel integration module. Refer to Instrument Panel Module Replacement in Body Control System. Did you complete the replacement? | -- | Go to Step 15 | -- |
17 |
Does the DTC reset? | -- | Go to Step 2 | System OK |
