GM Service Manual Online
For 1990-2009 cars only

Disassembly Procedure


    Object Number: 423457  Size: SH
  1. Remove the adjuster plug lock nut (5) from the adjuster plug (4).
  2. Remove the adjuster plug (4) from the gear assembly (1).
  3. Remove the adjuster spring (3) and the rack bearing (2).

  4. Object Number: 423458  Size: SH
  5. Remove the retaining ring (1) from the valve bore of the rack and pinion gear assembly (2).
  6. Remove the dust cover (4) from the bottom of the rack and pinion gear assembly (2).
  7. Remove the hex lock nut (3) from the lower end of the pinion and valve assembly while holding the stub shaft with a 14 mm crowfoot wrench.

  8. Object Number: 423459  Size: SH

    Important: When performing the following procedure, do not remove pinion and valve assembly from the rack and pinion gear assembly (5). Press the pinion and valve assembly only far enough to allow removal of the stub shaft bearing annulus (3) and the stub shaft seal (2).

  9. Using an arbor press (1), press on the threaded end of the pinion until removal of the following items is possible:
  10. 7.1. The stub shaft (4)
    7.2. The stub shaft seal (2)
    7.3. The stub shaft bearing annulus assembly (3)

Assembly Procedure

Tools Required

J 6222-A Stub Shaft Seal Protector


    Object Number: 423460  Size: SH
  1. Install the hex lock nut (1) onto the pinion while holding the valve stub shaft.
  2. Tighten
    Tighten the hex lock nut (1) to 30 N·m (22 lb ft).

  3. Install the dust cover (2) to the rack and pinion gear assembly.

  4. Object Number: 423461  Size: SH
  5. Install the stub shaft bearing annulus assembly (1) onto the valve stub shaft (2).

  6. Object Number: 423462  Size: SH
  7. Install J 6222-A onto the valve stub shaft.
  8. Lubricate the stub shaft seal (2) with grease.
  9. Install the stub shaft seal (2) into the rack and pinion gear assembly.
  10. Install the retaining ring (1) into the groove in the rack and pinion gear assembly.

  11. Object Number: 423457  Size: SH
  12. Lubricate the following items with lithium base grease:
  13. 8.1. The rack bearing (2)
    8.2. The adjuster spring (3)
    8.3. The adjuster plug (4)
  14. Install the following items into the gear assembly:
  15. 9.1. The rack bearing (2)
    9.2. The adjuster spring (3)
    9.3. The adjuster plug (4)

    Object Number: 423465  Size: SH
  16. Turn the adjuster plug (1) clockwise onto the rack and pinion gear assembly until the adjuster plug (1) bottoms in the rack and pinion gear assembly, then turn the adjuster plug (1) back 50 degrees to 70 degrees.
  17. Check the rotational torque on the pinion. The maximum pinion preload torque is 1.8 N·m (16 lb in).

  18. Object Number: 423457  Size: SH
  19. Install the adjuster plug lock nut (5) to the adjuster plug (4).
  20. Notice: Use the correct fastener in the correct location. Replacement fasteners must be the correct part number for that application. Fasteners requiring replacement or fasteners requiring the use of thread locking compound or sealant are identified in the service procedure. Do not use paints, lubricants, or corrosion inhibitors on fasteners or fastener joint surfaces unless specified. These coatings affect fastener torque and joint clamping force and may damage the fastener. Use the correct tightening sequence and specifications when installing fasteners in order to avoid damage to parts and systems.

    Tighten
    Finger tighten the adjuster plug lock nut (5) while holding the adjuster plug (4) stationary.