GM Service Manual Online
For 1990-2009 cars only

Diagnostic Instructions

    • Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.
    • Review Strategy Based Diagnosis for an overview of the diagnostic approach.
    •  Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P0117: Engine Coolant Temperature (ECT) Sensor Circuit Low Voltage

DTC P0118: Engine Coolant Temperature (ECT) Sensor Circuit High Voltage

Diagnostic Fault Information

Circuit

Short to Ground

High Resistance

Open

Short to Voltage

Signal Performance

ECT Sensor Signal

P0117

P0118

P0118

P0118

P0116, P0125, P0128

Low Reference

--

P0118

P0118

P0118

P0125, P0128

Typical Scan Tool Data

ECT Sensor Temperature

Circuit

Normal Range

Short to Ground

Open

Short to Voltage

ECT Sensor Signal

-39 to +120°C (-38 to +248°F)

150°C (302°F)

-40°C (-40°F)

-40°C (-40°F)

Low Reference

--

--

-40°C (-40°F)

-40°C (-40°F)

Circuit/System Description

The engine coolant temperature (ECT) sensor is a variable resistor that measures the temperature of the engine coolant. The engine control module (ECM) supplies 5 volts to the ECT signal circuit and supplies a ground to the low reference circuit.

Conditions for Running the DTC

P0117

    • The engine is running for greater than 10 seconds.
        OR
    • The ignition is ON when the intake air temperature (IAT) is less than 50°C (122°F).
    • This DTC runs continuously when the above conditions are met.

P0118

    • The engine is running for greater than 10 seconds.
        OR
    • The ignition is ON when the IAT is greater than 0°C (32°F).
    • This DTC runs continuously when the above conditions are met.

Conditions for Setting the DTC

P0117

The ECM detects that the ECT is greater than 149°C (300°F) for greater than 5 seconds.

P0118

The ECM detects that the ECT is less than -39°C (-38°F) for greater than 5 seconds.

Action Taken When the DTC Sets

DTCs P0117 and P0118 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P0117 and P0118 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

    •  Circuit Testing
    •  Connector Repairs
    •  Testing for Intermittent Conditions and Poor Connections
    •  Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

    Warning: Under pressure, the temperature of the solution in the radiator can be considerably higher, without boiling. Removing the radiator cap while the engine is hot (pressure is high), will cause the solution to boil instantaneously, with explosive force. The solution will spew out over the engine, fenders, and the person removing the cap. Serious bodily injury may result. Flammable antifreeze, such as alcohol, is not recommended for use at any time. Flammable antifreeze could cause a serious fire.

  1. Turn OFF the ignition.
  2. Inspect the cooling system surge tank for the proper engine coolant level. Refer to Cooling System Leak Testing and Cooling System Draining and Filling.
  3. Turn ON the ignition, with the engine OFF.
  4. Use the scan tool to verify the proper operation of the engine cooling system fans.
  5. Turn OFF the ignition.
  6. Verify the proper heat range, and the operation of the thermostat. Refer to Thermostat Diagnosis.

Circuit/System Testing

Note: All electrical components and accessories must be turned OFF and allowed to power down.

  1. Ignition OFF, disconnect the ECT harness connector at the ECT sensor.
  2. Ignition OFF, test for less than 5 ohms between the low reference circuit terminal A and ground.
  3. If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the ECM.
  4. Ignition ON, verify the scan tool ECT Sensor parameter is less than -39°C (-38°F).
  5. If greater than the specified range, test the signal circuit for a short to ground. If the circuit tests normal, replace the ECM.
  6. Install a 3A fused jumper wire between the signal circuit terminal B and the low reference circuit terminal A. Verify the scan tool ECT Sensor parameter is greater than 149°C (300°F).
  7. If less than the specified range, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the ECM.
  8. If all circuits test normal, test or replace the ECT sensor.

Component Testing

Measure and record the resistance of the ECT sensor at various ambient temperatures, then compare those measurements to the Temperature vs Resistance Table. Refer to Temperature Versus Resistance.

Repair Instructions

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.

    •  Engine Coolant Temperature Sensor Replacement
    •  Control Module References for ECM replacement, setup, and programming