The manifold absolute pressure (MAP) sensor responds to changes in intake manifold pressure which gives an indication of the engine load. The MAP sensor has a 5-volt reference circuit, a low reference circuit, and a signal circuit. The powertrain control module (PCM) supplies 5 volts to the MAP sensor on the 5-volt reference circuit and provides a ground on the low reference circuit. The MAP sensor provides a signal to the PCM on the MAP sensor signal circuit which is relative to the pressure changes in the manifold.

With low MAP, such as during idle or deceleration, the PCM should detect a low MAP sensor signal voltage. With high MAP, such as ignition ON, engine OFF or wide open throttle (WOT), the PCM should detect a high MAP sensor signal voltage. This MAP sensor will indicate pressure between 12-103 kPa. The MAP sensor is also used in order to calculate the barometric pressure (BARO) when the ignition switch is turned ON, with the engine OFF. The BARO reading may also be updated whenever the engine is operated at WOT. The PCM monitors the MAP sensor signal for voltage outside of the normal range.

DTC P0106 is a Type B DTC.

DTC P0106 is a Type B DTC.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Special Tools

Important: Verify that the engine is in good mechanical condition before continuing with this diagnostic.

1. Verify that the following DTCs are not set: DTC P0641 or P0651.

⇒	If any of the DTCs are set, refer to DTC P0641 or P0651.

2. Verify the integrity of the entire air induction system by inspecting for the following conditions:

•	Any damaged components

•	Loose or improper installation

•	An air flow restriction

•	Any vacuum leak

•	Improperly routed vacuum hoses

•	In cold climates, inspect for any snow or ice buildup.

3. Verify that restrictions do not exist in the MAP sensor port or vacuum source.
4. Verify that restrictions do not exist in the exhaust system. Refer to Restricted Exhaust.
5. The BARO that is used by the PCM to calculate the air flow models is initially based on the MAP sensor at ignition ON. When the engine is running, the PCM will continually update the BARO value near WOT using the MAP sensor and a calculation. A skewed MAP sensor will cause the BARO value to be inaccurate. Determine the current vehicle testing altitude. Ignition ON, observe the scan tool BARO Sensor parameter. Compare the parameter to the Altitude Versus Barometric Pressure table.
6. A skewed MAP sensor will also cause the first and second intake manifold models to disagree with the actual MAP sensor measurements. Use the scan tool and compare the MAP Sensor parameter to a known good vehicle, under various operating conditions.

Important: All electrical components and accessories must be turned OFF, and allowed to power down.

1. Ignition OFF, disconnect the harness connector at the MAP sensor.
2. Ignition OFF, test for less than 5 ohms between the low reference circuit terminal A and ground.

⇒	If greater than the specified range, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the PCM.

3. Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal C and ground.

⇒	If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.

⇒	If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the PCM.

4. Verify the scan tool MAP parameter is less than 12 kPa.

⇒	If greater than the specified range, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the PCM.

5. Install a 3A fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal C. Verify the scan tool MAP parameter is greater than 103 kPa.

⇒	If less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the PCM.

6. If all circuits test normal, test or replace the MAP sensor.

1. Turn ON the ignition, with the engine OFF, and remove the MAP sensor.
2. Install a 3A fused jumper wire between the 5-volt reference circuit terminal C and the corresponding terminal of the MAP sensor.
3. Install a jumper wire between the low reference circuit terminal A of the MAP sensor and ground.
4. Install a jumper wire at terminal B of the MAP sensor.
5. Connect a DMM between the jumper wire from terminal B of the MAP sensor and ground.
6. Install the J 23738-A or J 35555 to the MAP sensor vacuum port. Slowly apply vacuum to the sensor while observing the voltage on the DMM. The voltage should vary between 0-5.2 volts, without any spikes or dropouts.

⇒	If the voltage is not within the specified range or is erratic, replace the MAP sensor.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.