The engine control module (ECM) provides ignition voltage to the coil side of the fuel pump relay whenever the engine is cranking or running. The control module enables the fuel pump relay as long as the engine is cranking or running, and ignition system reference pulses are received. If no ignition system reference pulses are received, the control module turns OFF the fuel pump. The fuel pump relay control circuit is equipped with a feedback circuit that is pulled up to 2.5 volts within the ECM. The ECM can determine if the control circuit is open, shorted to ground, or shorted to a voltage by monitoring the feedback voltage.

P0627

The ECM detects the voltage on the fuel pump relay control circuit is within a predetermined range when the control circuit is commanded OFF. The condition exists for less than 4 seconds.

P0628

The ECM detects that the fuel pump relay control circuit is shorted to ground. The condition exists for less than 4 seconds.

P0629

The ECM detects that the fuel pump relay control circuit is shorted to a voltage. The condition exists for less than 4 seconds.

DTCs P0627, P0628 and P0629 are Type C DTCs.

DTCs P0627, P0628 and P0629 are Type C DTCs.

The following table illustrates the ECM connector locations:

If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the circuit status for the component with a scan tool. The circuit status parameter changes from OK or Indeterminate to Fault if there is a condition with the circuit or a connection.

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

1. Ignition ON, observe the scan tool DTC information. Verify DTC P2105 is not set.

⇒	If DTC P2105 is set, refer to refer to DTC P2105 for further diagnosis.

2. Command the Fuel Pump Relay ON and OFF with a scan tool. You should hear an audible click.
3. Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that are captured in the Freeze Frame/Failure Records Data List.

1. Ignition OFF, disconnect the fuel pump relay.
2. Connect a test lamp between the control circuit of the fuel pump relay and ground.
3. Ignition ON, command the fuel pump ON and OFF with a scan tool. The test lamp should turn ON and OFF as commanded.

⇒	If the test lamp remains OFF all the time, test for a short to ground or an open/high resistance on the control circuit. If circuit/connections test normal, replace the ECM.

⇒	If the test lamp remains ON all the time, test for a short to voltage on the control circuit. If circuit/connections test normal, replace the ECM.

4. Ignition OFF, connect a test lamp between the fuel pump relay control circuit and the ground circuit of the fuel pump relay.
5. Ignition ON, command the fuel pump ON and OFF with a scan tool. The test lamp should turn ON and OFF as commanded.

⇒	If the test lamp does not turn ON when commanded, repair the open/high resistance in ground circuit of the fuel pump relay.

6. If all circuits/connections test normal, test or replace the fuel pump relay.

1. Test for 70-110 ohms of resistance between terminals 85 and 86 of the fuel pump relay.

⇒	If not within the specified range, replace the fuel pump relay.

2. Test for infinite resistance between the following terminals of the fuel pump relay:

•

30 and 86

•

30 and 87

•

30 and 85

•

85 and 87

⇒	If continuity is detected, replace the fuel pump relay.

3. Connect a 20A fused jumper wire from the positive terminal of the battery to relay terminal 85. Connect a jumper wire from the negative terminal of the battery to relay terminal 86. Test for less than 2 ohms between terminals 30 and 87 of the relay.

⇒	If greater than the specified range, replace the fuel pump relay.

Perform the Diagnostic Repair Verification after completing the diagnostic procedure.