Air Conditioning Compressor Replacement L26

Special Tools

J 39400-A Halogen Leak Detector

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Remove the drive belts. Refer to Drive Belt Replacement .
3. Remove the splash shield from the right side of the engine. Refer to Engine Splash Shield Replacement .
4. Remove the hose nut from the A/C compressor.
5. Remove the hose from the A/C compressor.

Important: Remove and discard all sealing washers.

6. Disconnect the electrical connector from the A/C compressor.



7. Loosen the rear mounting bolt from the A/C compressor.
8. Remove the front mounting bolt from the A/C compressor.
9. Remove the front mounting nut from the A/C compressor.
10. Remove the A/C compressor.

Important: Replacement compressors are shipped with polyalkylene glycol (PAG) oil.

11. If replacing the compressor, balance the compressor oil. Refer to Air Conditioning Compressor Oil Balancing .

Notice: Refer to Fastener Notice in the Preface section.

1. Install the compressor drain plug.

Tighten
Tighten the drain plug to 16 N·m (12 lb ft).

2. Position the A/C compressor onto the front A/C compressor mounting stud and the rear A/C compressor mounting bolt.
3. Install the A/C compressor front bolt.

Tighten
Tighten the bolts to 50 N·m (36 lb ft).

4. Install the A/C compressor front mounting nut.

Tighten
Tighten the nut to 50 N·m (36 lb ft).

5. Tighten the A/C compressor rear bolt.

Tighten
Tighten the bolt to 50 N·m (36 lb ft).

6. Install new sealing washers. Refer to Sealing Washer Replacement .



7. Install the hose to the A/C compressor.
8. Install the nut to the A/C compressor hose.

Tighten
Tighten the nut to 17 N·m (12.5 lb ft).

9. Connect the electrical connector to the A/C compressor.
10. Install the splash shield to the right side of the engine. Refer to Engine Splash Shield Replacement .
11. Install the drive belts. Refer to Drive Belt Replacement .
12. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
13. Leak test the fittings of the component using J 39400-A .

Air Conditioning Compressor Replacement LY7

Special Tools

J 39400-A Halogen Leak Detector

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging .
2. Remove the drive belts. Refer to Drive Belt Replacement .
3. Remove the splash shield from the right side of the engine. Refer to Engine Splash Shield Replacement .
4. Disconnect the electrical connector from the A/C compressor.



5. Remove the compressor hose nut from the A/C compressor.

Important: Remove and discard all sealing washers.

6. Remove the compressor hose from the A/C compressor.



7. Loosen the rear mounting bolt (1) from the A/C compressor.
8. Remove the front mounting bolt (3) from the A/C compressor.
9. Remove the front mounting nut (2) from the A/C compressor.
10. Remove the A/C compressor.

Important: Replacement compressors are shipped with polyalkylene glycol (PAG) oil

11. If replacing the compressor, balance the compressor oil. Refer to Air Conditioning Compressor Oil Balancing .

Notice: Refer to Fastener Notice in the Preface section.

1. Install the compressor drain plug.

Tighten
Tighten the drain plug to 16 N·m (12 lb ft).




2. Position the A/C compressor onto the front A/C compressor mounting stud and the rear A/C compressor mounting bolt (1).
3. Install the A/C compressor front bolt (3).

Tighten
Tighten the bolts to 50 N·m (36 lb ft).

4. Install the A/C compressor front mounting nut (2).

Tighten
Tighten the nut to 50 N·m (36 lb ft).

5. Tighten the A/C compressor rear bolt.

Tighten
Tighten the bolt to 50 N·m (36 lb ft).




6. Install new sealing washers. Refer to Sealing Washer Replacement .
7. Install the compressor hose to the A/C compressor.
8. Install the nut to the A/C compressor hose.

Tighten
Tighten the nut to 17 N·m (12.5 lb ft).

9. Connect the electrical connector to the A/C compressor.
10. Install the splash shield to the right side of the engine. Refer to Engine Splash Shield Replacement .
11. Install the drive belts. Refer to Drive Belt Replacement .
12. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging .
13. Leak test the fittings of the component using J 39400-A .

Air Conditioning Compressor Replacement LS4

Special Tools

J 39400-A Halogen Leak Detector

1. Recover the refrigerant. Refer to Refrigerant Recovery and Recharging.
2. Remove the drive belt. Refer to Drive Belt Replacement - Accessory.
3. Remove the lower radiator air baffle and deflector. Refer to Radiator Air Lower Baffle and Deflector Replacement.



4. Disconnect the A/C compressor electrical connector.



5. Remove the A/C compressor hose nut from the A/C compressor.




Important: Remove and discard all sealing washers.

6. Remove the A/C compressor hose from the A/C compressor.



7. Remove the stud from the A/C compressor.



8. Loosen the rear mounting bolt from the A/C compressor.



9. Remove the front mounting bolt from the A/C compressor.
10. Remove the front mounting nut from the A/C compressor.
11. Remove the front A/C compressor mounting stud.
12. Install a floor stand under the right front cradle.
13. Loosen the right front cradle bolt and lower the cradle.
14. Remove the A/C compressor.

Important: Replacement compressors are shipped with polyalkylene glycol (PAG) oil.

15. If replacing the compressor, balance the compressor oil. Refer to Air Conditioning Compressor Oil Balancing.

Notice: Refer to Fastener Notice in the Preface section.

1. Install the compressor drain plug.

Tighten
Tighten the drain plug to 16 N·m (12 lb ft).





Important: Install the A/C compressor ensuring that the back of the A/C compressor is inserted onto the bolt. Do not tighten the bolt at this time.

2. Install the A/C compressor into the vehicle.




Important: Do not tighten at this time.

3. Install the front A/C compressor mounting bolt.
4. Install the front A/C compressor mounting stud.

Tighten
Tighten the stud to 10 N·m (89 lb in).

5. Install the front A/C compressor nut.

Tighten

•	Tighten the nut to 50 N·m (36 lb ft).

•	Tighten the front bolt to 50 N·m (36 lb ft).

•	Tighten the rear bolt to 50 N·m (36 lb ft).




6. Connect the A/C compressor electrical connector.
7. Raise the cradle into position and tighten the bolt.

Tighten
Tighten the bolt to 145 N·m (107 lb ft).

8. Remove the floor stand from under the vehicle.



9. Install the stud to the back of the A/C compressor.

Tighten
Tighten the stud to 10 N·m (89 lb in).




10. Install new sealing washers. Refer to Sealing Washer Replacement.
11. Install the A/C compressor hose to the A/C compressor.



12. Install the A/C compressor hose nut.

Tighten
Tighten the nut to 17 N·m (12.5 lb ft).

13. Install the lower radiator air baffle and deflector. Refer to Radiator Air Lower Baffle and Deflector Replacement.
14. Install the drive belt. Refer to Drive Belt Replacement - Accessory.
15. Evacuate and recharge the A/C system. Refer to Refrigerant Recovery and Recharging.
16. Leak test the fittings of the component using J 39400-A .