Diagnostic Instructions
| • | Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure. |
| • | Review Strategy Based Diagnosis for an overview of the diagnostic approach. |
| • | Diagnostic Procedure Instructions provides an overview of each diagnostic category. |
DTC Descriptors
DTC C0277 06: Brake Pedal Position Sensor Circuit Short to Ground or OpenDTC C0277 07: Brake Pedal Position Sensor Circuit Voltage Above Threshold
DTC C0277 09: Brake Pedal Position Sensor Circuit Rate of Change Above Threshold
DTC C0277 4B: Brake Pedal Position Sensor Calibration Not Learned
DTC C0890 03: Device Voltage Reference Output 3 Circuit Voltage Below Threshold
DTC C0890 07: Device Voltage Reference Output 3 Circuit Voltage Above Threshold
Diagnostic Fault Information
Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|---|---|---|---|---|
Brake Position Sensor 5-Volt Reference | C0277 06, C0890 03 | C0277 06 | C0277 06*, C0890 07 | -- |
Brake Apply Sensor Signal | C0277 06 | C0277 06 | C0277 07 | C0277 09, C0277 4B |
Brake Position Sensor Low Reference | -- | C0277 06* | -- | -- |
* Stop Lamps Are Always ON | ||||
Circuit/System Description
The body control module (BCM) provides a 5-volt reference voltage and a low reference signal to the brake pedal position sensor (BPPS). When the brake pedal is applied, the BPPS sends a variable voltage signal, that will increase as the brake pedal is applied, through the brake apply sensor signal circuit to the BCM. In response to this signal, the BCM applies B+ to the stop lamps, center high mounted stop lamp (CHMSL), transmission control module (TCM), and engine control module (ECM). The stop lamps will not operate unless the ignition is in the ON position.
Conditions for Running the DTC
The ignition is ON.
Conditions for Setting the DTC
C0277 06
The BCM detects a short to ground or open on the brake apply sensor signal circuit, or a short to ground or an open in the brake position sensor 5-volt reference circuit.
C0277 07
The BCM detects short to voltage on the brake apply sensor signal circuit.
C0277 09
The BCM detects the brake pedal position sensor reading is erroneous.
C0277 4B
The BCM detects that the brake pedal position sensor home position is not learned.
C0890 03
The BCM detects a short to ground in the brake position sensor 5-volt reference circuit.
C0890 07
The BCM detects a short to voltage in the brake position sensor 5-volt reference circuit.
Action Taken When the DTC Sets
| • | The Service Vehicle Soon indicator is commanded ON. |
| • | If the DTC sets while the vehicle is running, the BCM will activate the brake lights when the vehicle transmission is not in the PARK position and the vehicle is not accelerating. |
| • | For DTC C0277 4B, the stop lamps may not activate at the expected brake pedal positions. |
Conditions for Clearing the DTC
| • | For DTC C0277 4B, a successful brake pedal position sensor calibration has been performed. |
| • | A DTC will not clear the current status until the next ignition cycle. |
| • | A history DTC will clear once 100 consecutive malfunction-free ignition cycles have occurred. |
Diagnostic Aids
The stop lamps will not illuminate unless the ignition is in the ON position.
Reference Information
Schematic Reference
Connector End View Reference
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References for scan tool information
Circuit/System Testing
C0277 06, C0277 07, and C0890 03
- Ignition OFF, disconnect the harness connector at the brake pedal position sensor.
- Ignition OFF, verify that a test lamp illuminates between the low reference circuit terminal C and B+.
- Ignition ON, test for 4.8-5.2 volts between the 5-volt reference circuit terminal A and ground.
- Verify the scan tool BPP Sensor parameter is less than 2 counts.
- Install a 3A fused jumper wire between the signal circuit terminal B and the 5-volt reference circuit terminal A. Verify the scan tool BPP Sensor parameter is greater than 1000 counts.
- If all circuits test normal, test or replace the brake pedal position sensor.
| ⇒ | If the test lamp does not illuminate, test the low reference circuit for an open/high resistance. If the circuit tests normal, replace the BCM. |
| ⇒ | If less than the specified range, test the 5-volt reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
| ⇒ | If greater than the specified range, test the 5-volt reference circuit for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If greater than the specified value, test the signal circuit terminal B for a short to voltage. If the circuit tests normal, replace the BCM. |
| ⇒ | If less than the specified range, test the signal circuit for short to ground or an open/high resistance. If the circuit tests normal, replace the BCM. |
C0277 09
- Replace the brake pedal position sensor.
- Perform the scan tool BPP Sensor Calibration procedure. Refer to Brake Pedal Position Sensor Calibration.
- Operate the vehicle within the Conditions for Running the DTC and verify the DTC does not reset.
| ⇒ | If the DTC resets, replace the BCM. |
C0277 4B
- Ignition ON, verify that no other brake pedal position sensor DTCs are set.
- Perform the scan tool BPP Sensor Calibration procedure. Refer to Brake Pedal Position Sensor Calibration.
- Observe the scan tool BPPS Status parameter. The reading should be Learned.
| ⇒ | If other brake pedal sensor DTCs are set, diagnosis those DTCs first. |
| ⇒ | If not the specified value, replace the brake pedal position sensor. If the DTC resets, replace the BCM. |
Repair Instructions
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • | Control Module References for BCM replacement, setup, and programming |
