GM Service Manual Online
For 1990-2009 cars only

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. This step tests the output from the blower motor switch. Loss of blower motor switch output would indicate a malfunctioning switch or a circuit malfunction in the supply voltage to the switch.

  2. There are 2 ignition 3 voltage circuits at the HVAC control module. Test the circuit that provides supply voltage to the blower motor switch.

Step

Action

Yes

No

Schematic Reference: HVAC Schematics

Connector End View Reference: HVAC Connector End Views

DEFINITION: The blower motor is inoperative in all speed positions.

1

Did you perform the HVAC Diagnostic System Check?

Go to Step 2

Go to Diagnostic System Check - HVAC Systems - Manual

2

  1. Turn ON the ignition, with the engine OFF.
  2. Place the blower motor switch in each speed position.

Does the blower motor operate in any of the speed positions?

Go to Blower Motor Malfunction

Go to Step 3

3

  1. Turn OFF the ignition.
  2. Disconnect the blower motor.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the blower motor supply voltage circuit and a good ground.
  5. Place the blower motor switch in the minimum speed position.

Does the test lamp illuminate?

Go to Step 4

Go to Step 6

4

Connect a test lamp between the blower motor supply voltage circuit and the blower motor ground circuit.

Does the test lamp illuminate?

Go to Step 9

Go to Step 5

5

Test the ground circuit of the blower motor resistor assembly for an open or high resistance. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 10

6

  1. Turn OFF the ignition.
  2. Disconnect the blower motor resistor.
  3. Turn ON the ignition, with the engine OFF.
  4. Place the blower motor switch in the minimum speed position.
  5. Connect a test lamp between the low blower motor control circuit of the blower motor resistor assembly and a good ground.

Does the test lamp illuminate?

Go to Step 10

Go to Step 7

7

  1. Turn OFF the ignition.
  2. Disconnect the HVAC control module.
  3. Turn ON the ignition, with the engine OFF.
  4. Connect a test lamp between the ignition 3 voltage circuit of the blower motor switch and a good ground.

Does the test lamp illuminate?

Go to Step 12

Go to Step 8

8

Test each of the blower motor control circuits for a short to ground. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 14

9

Inspect for poor connections at the harness connector of the blower motor. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 14

10

Test the blower motor harness of the blower motor resistor assembly for an open. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 11

11

Inspect for poor connections at the harness connector of the blower motor resistor assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 15

12

Inspect for poor connections at the harness connector of the HVAC control module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.

Did you find and correct the condition?

Go to Step 17

Go to Step 16

13

Repair the ignition 3 voltage circuit of the blower motor switch. Refer to Wiring Repairs in Wiring Systems.

Did you complete the repair?

Go to Step 17

--

14

Replace the blower motor. Refer to Blower Motor Replacement in Heating, Ventilation and Air Conditioning.

Did you complete the replacement?

Go to Step 17

--

15

Replace the blower motor resistor assembly. Refer to Blower Motor Resistor Assembly Replacement in Heating, Ventilation and Air Conditioning.

Did you complete the replacement?

Go to Step 17

--

16

Replace the HVAC control module. Refer to HVAC Module Assembly Replacement .

Did you complete the replacement?

Go to Step 17

--

17

Operate the system in order to verify the repair.

Did you correct the condition?

System OK

Go to Step 3