GM Service Manual Online
For 1990-2009 cars only

Circuit Description

The engine control module (ECM) provides ignition voltage to the coil side of the fuel pump relay whenever the engine is cranking or running. The control module enables the fuel pump relay as long as the engine is cranking or running, and ignition system reference pulses are received. If no ignition system reference pulses are received, the control module turns OFF the fuel pump.

The fuel pump relay control circuit is equipped with a feedback circuit that is pulled up to 2.5 volts within the ECM. The ECM can determine if the control circuit is open, shorted to ground, or shorted to a voltage by monitoring the feedback voltage. If the ECM detects that the control circuit voltage is within a predetermined range when the circuit is commanded OFF, this DTC sets.

DTC Descriptor

This diagnostic procedure supports the following DTC:

DTC P0627 Fuel Pump Relay Control Circuit

Conditions for Running the DTC

    • The engine speed is more than 80 RPM.
    • The ignition 1 voltage is between 10-18 volts.
    • The ECM has commanded the fuel pump relay ON and OFF at least once during the ignition cycle.
    • The above conditions are met for more than 1 second.
    • DTC P0627 runs continuously once the above conditions are met.

Conditions for Setting the DTC

    • The ECM detects the voltage on the fuel pump relay control circuit is within predetermined range when the circuit is commanded OFF.
    • The condition exists for less than 4 seconds.

Action Taken When the DTC Sets

    • The control module illuminates the malfunction indicator lamp (MIL) on the second consecutive ignition cycle that the diagnostic runs and fails.
    • The control module records the operating conditions at the time the diagnostic fails. The first time the diagnostic fails, the control module stores this information in the Failure Records. If the diagnostic reports a failure on the second consecutive ignition cycle, the control module records the operating conditions at the time of the failure. The control module writes the operating conditions to the Freeze Frame and updates the Failure Records.

Conditions for Clearing the MIL/DTC

    • The control module turns OFF the malfunction indicator lamp (MIL) after 4 consecutive ignition cycles that the diagnostic runs and does not fail.
    • A current DTC, Last Test Failed, clears when the diagnostic runs and passes.
    • A history DTC clears after 40 consecutive warm-up cycles, if no failures are reported by this or any other emission related diagnostic.
    • Clear the MIL and the DTC with a scan tool.

Diagnostic Aids

The following table illustrates the ECM connector locations:

ECM Connector Location

C2

C1

Front of Vehicle

    • Use the J 35616-A/BT-8637 Connector Test Adapter Kit for any test that requires probing the ECM harness connector or a component harness connector.
    • If the condition is intermittent, move the related harnesses and connectors, with the engine operating, while monitoring the circuit status for the component with a scan tool. The circuit status parameter changes from OK or Indeterminate to Fault if there is a condition with the circuit or a connection. The ODM information is in the output driver module (ODM) data list.
    • For an intermittent condition, refer to Intermittent Conditions .

Test Description

The number below refers to the step number on the diagnostic table.

  1. This step verifies that the control module is providing voltage to the fuel pump relay.

  2. This step tests the ground circuit of the fuel pump relay.

Step

Action

Yes

No

Schematic Reference: Engine Controls Schematics

Connector End View Reference: Engine Control Module Connector End Views or Engine Controls Connector End Views

1

Did you perform the Diagnostic System Check - Vehicle?

Go to Step 2

Go to Diagnostic System Check - Vehicle

2

Important: 

   • DTC P2105 may cause this DTC to set. Refer to Diagnostic System Check - Vehicle .
   • Additional DTCs may set when using the Fuel Pump output control.

  1. Turn ON the ignition, with the engine OFF.
  2. Command the fuel pump ON and OFF with a scan tool.

Does the fuel pump relay turn ON and OFF with each command?

Go to Step 3

Go to Step 4

3

  1. Observe the Freeze Frame/Failure Records for this DTC.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 4

Go to Diagnostic Aids

4

  1. Turn OFF the ignition.
  2. Disconnect the fuel pump relay.
  3. Turn ON the ignition, with the engine OFF.
  4. Probe the control circuit of the fuel pump relay with a test lamp connected to a good ground.
  5. Command the fuel pump ON and OFF with a scan tool.

Does the test lamp turn ON and OFF when commanded?

Go to Step 5

Go to Step 6

5

  1. Connect a test lamp between the control circuit and the ground circuit of the fuel pump relay.
  2. Command the fuel pump ON and OFF with a scan tool.

Does the test lamp turn ON and OFF when commanded?

Go to Step 7

Go to Step 9

6

Test the control circuit of the fuel pump relay for an open or a high resistance. Refer to Circuit Testing and Wiring Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 8

7

Test for an intermittent and for a poor connection at the fuel pump relay. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 10

8

Test for an intermittent and for a poor connection at the engine control module (ECM). Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .

Did you find and correct the condition?

Go to Step 12

Go to Step 11

9

Repair the open or high resistance in the ground circuit of the fuel pump relay. Refer to Wiring Repairs .

Did you complete the repair?

Go to Step 12

--

10

Replace the fuel pump relay.

Did you complete the replacement?

Go to Step 12

--

11

Replace the ECM. Refer to Control Module References for replacement, setup, and programming.

Did you complete the replacement?

Go to Step 12

--

12

  1. Clear the DTCs with a scan tool.
  2. Turn OFF the ignition for 30 seconds.
  3. Start the engine.
  4. Operate the vehicle within the Conditions for Running the DTC. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records.

Did the DTC fail this ignition?

Go to Step 2

Go to Step 13

13

Observe the Capture Info with a scan tool.

Are there any DTCs that have not been diagnosed?

Go to Diagnostic Trouble Code (DTC) List - Vehicle

System OK